Clare Controls amp.14150 User Manual Download Page 2

 

Copyright 

© 11DEC14 Clare Controls, Inc. All rights reserved. 

This document may not be copied in whole or in part or otherwise 
reproduced without prior written consent from Clare Controls, Inc., 
except where specifically permitted under U.S. and international 
copyright law.   

Trademarks  

The amp.14150 name is a trademark of Clare Controls, Inc. 

Manufacturer 

Clare Controls, Inc. 
7519 Pennsylvania Ave., Suite 104, Sarasota, FL 34243, USA 

Version 

This document applies to amp.14150 version 01. 

Compliance

 

 

FCC compliance 

This device complies with part 15 of the FCC Rules. Operation is 
subject to the following two conditions: (1) This device may not cause 
harmful interference, and (2) this device must accept any interference 
received, including interference that may cause undesired operation. 

EU compliance 

 

 

 

2002/96/EC (WEEE directive): 

Products marked with this symbol 

cannot be disposed of as unsorted municipal waste in the European 
Union. For proper recycling, return this product to your local supplier 
upon the purchase of equivalent new equipment, or dispose of it at 
designated collection points. For more information see: 
www.recyclethis.info. 

Contact information 

For contact information, see www.clarecontrols.com. 

 

 

 

Summary of Contents for amp.14150





















Reviews: