background image

15

Instructions for installer - CEX9 - 801040 - January 2019 v1.10 Art.no:

 9120-25687

9. Service menu

Menu item order of “Service menu“:

Flow

Power

Temp in

Temp out

Control value

Power limit

Diagnostics

Lock level

Software version

Radio channel

Received strength

Backlight

Temperature limit

Signal

on the power electronics, as specified in the chapter “Deactivation of the lock 
level”.

“nr“: Software version

Information about installed software version.

“Ch“: Radio channel

(with wireless module only) 
Information about the current radio channel of the water heater and its remote control.

“rS“: Received strength

(with wireless module only) 
Information about the current signal quality of the remote control as percentage. 
Depending on the distance between remote control and water heater the value varies 
between 10 % and 100 %.

“tL”: Temperature limit

The maximum setable temperature can be reduced to any value within the tempera-
ture limit.
The Lock Level must be activated by placing the jumper to enable the limitation.

“IIC“: Signal

Information about the quality of the radio contact when a diagnostic display is con-
nected.

10. Environment and recycling

Your product was manufactured from high-quality, reusable materials and compo-
nents. Please respect in case of discarding that electrical devices should be disposed of 
separately from household waste at the end of their service life. Therefore, please take 
this device to a municipal collection point that accepts electronic scrap. Disposing it 
correctly will support environmental protection and will prevent any potential negative 
effects on human beings and the environment that could arise from inappropriate han-
dling of these devices at the end of their service life. Please contact your local authority 
for further details of your nearest designated collection point or recycling site. 
Business customers: If you wish to discard equipment, please contact your dealer or 
supplier for further information.

Summary of Contents for 27900





















Reviews: