Claas LEXION Repair Manual Download Page 13

299 211.0 RHB klappbares SW 4,50 m - 5,40 m LEXION 

1.2.1

Safety Rules

SAFETY RULES

Important information

The instructions contained in this manual 
should be carefully read and observed by all 
persons involved with the operation, mainte-
nance and inspection of this machine in order 
to prevent accidents. In particular, read the 
section “Safety rules”.

The use of spare parts, accessories and 
ancillary equipment other than genuine CLAAS 
products or those which have been tested and 
approved by CLAAS, may change the specified 
design characteristics of this CLAAS machine 
or detract from its functional performance, with 
a possible adverse effect on the active and/or 
passive operational safety of the machine and 
its occupational safety standards (accident pre-
vention).

CLAAS is in no way liable for any damage or 
personal injury caused through the use of other 
than original or approved CLAAS parts, acces-
sories and ancillary equipment.

Technical data, dimensions and weights are 
given as an indication only. CLAAS reserve 
the right to make changes subsequently as 
technical developments continue. Responsi-
bility for errors or omissions not accepted. 

Front, rear, right and left refer to the direction 
of forward travel.

Safety Rules

Summary of Contents for LEXION
































Reviews: