Citrix ByteMobile T1010 Installation, Configuration And Administration Download Page 141

Page: 141 / 172

T-Series Traffic Director Installation, Configuration and Administration Guide

B-1

B. Replacement Parts

Replacement Parts

This appendix has the following sections:

•

Replaceable Components List

•

Replacing an AC Power Supply

•

Replacing a DC Power Supply

Replaceable Components List

The following table lists the replaceable components that you may order from Bytemobile.
Items in green (Expert Edition) are replaceable/orderable by Bytemobile only.

Table B-2

Replacement Components

Component

Part Number

10GBase-LR SFP+ Transceiver (1310nm, SMF). For
10Gbps Ethernet connection over single mode fiber optic
cable, up to 10km

Contact Bytemobile

10GBase-SR SFP+ Transceiver (850nm, MMF). For
10Gbps Ethernet connection over multi mode fiber optic
cable, distance up to 300m

SFP+ Direct Attach Cable (DAC), 5m

SFP+ Direct Attach Cable (DAC), 3m

SFP+ Direct Attach Cable (DAC), 1m

T1010 AC Power Supply

T1010 DC Power Supply

T1100 AC Power Supply

T1100 DC Power Supply

T1200 AC Power Supply

T1200 DC Power Supply

Summary of Contents for ByteMobile T1010













































































































































































Search results

Summary of Contents for ByteMobile T1010

Reviews:

Brands by name

Popular brands

Citrix ByteMobile T1010, Installation, Configuration And Administration

Search results

Summary of Contents for ByteMobile T1010

Reviews:

Brands by name

Popular brands