manualshive.com logo in svg

Citizen MLT-288, Service Manual, Page: 14 / 25

Share
Download
Citizen MLT-288 Service Manual Download Page 14

MLT-288 Service Manual

10

Chapter 3  Disassembling and Reassembling

Pay attention to the following matters in maintenance work

Caution:

(1) Do not disassemble, reassemble, nor adjust the printer without reasons, if it works normally.

Do not undo carelessly screws for fixing components in particular.

(2) Upon completion of inspections, be sure to check the printer for an anomaly before turning power on.

(3) Never print without setting paper to the printer.

(4) Confirm that paper has been set normally.

(5) Be careful not to leave parts, screws, or others used for maintenance work in the printer.

(6) In handling the print head, do not use gloves that are easy to generate static electricity.

(7) In disassembling and reassembling work, check cables and cords for damage or defects, and do not lay

them facibily

3-1  Tool List

* (+) Screwdriver (No. 0).
* Pincette.
* Mini-radio-plier.
* Oil brush.
* Mini-nipper.

3-2  Procedure for Disassembling

For disassembling the printer, remove parts from the frame assembly according to 3-3 “Procedure for
Reassembling”, but in the opposite order.

3-3  Procedure for Reassembling

Parts names used in the explanation are based on those in shown in “Parts List” in Chapter 5.  These part names are
commonly used over this service manual.

Summary of Contents for MLT-288


























Reviews:

No comments