manualshive.com logo in svg

Citizen iDP-3110, User Manual

Share
Download
Citizen iDP-3110 User Manual Download Page 10

iDP3110 User's Manual

 CITIZEN

5

3.2  Part Descriptions

1.  DC Jack

Insert the output plug of the AC adapter attached.

2.  Power Switch

When switched ON, power is supplied to the printer, starting the initializing operation.

3.  Power Lamp

Lighted when power is turned ON and goes out when turned OFF.

4.  SEL Lamp

Lighted when printer is in the selected condition (ON-LINE).

Printer becomes operational only when this lamp is on.

5.  LF Switch 

Paper is fed when switch is pressed (de-select condition only). Used to supply paper or to
insert some space in the output.

6.  SEL Switch

Printer is selected (ON-LINE) by pressing this switch.

Printer is de-selected (OFF-LINE) by pressing the switch again.

7.  Interface Connector

Printer is connected to various hosts via cables.

Please ensure that both the printer and the host are turned off before connecting.

8.  Printer Cover

Opened to exchange ribbon cassette and paper roll.

Summary of Contents for iDP-3110





































Reviews:

No comments

Brands by name

Popular brands

Load more brands