Cisco WS-C2950-24 Configuration Manual Download Page 246 | Manualshive

Page: 246 / 360

background image

Chapter 8 Configuring VLANs

Using VTP

8-14

Catalyst 2900 Series XL and Catalyst 3500 Series XL Software Configuration Guide

78-6511-05

VTP Modes and Mode Transitions

You can configure a supported switch to be in one of the VTP modes listed in

Table 8-4

.

Table 8-4

VTP Modes

VTP Mode

Description

VTP server

In this mode, you can create, modify, and delete VLANs and
specify other configuration parameters (such as VTP version)
for the entire VTP domain. VTP servers advertise their
VLAN configurations to other switches in the same VTP
domain and synchronize their VLAN configurations with
other switches based on advertisements received over trunk
links.

In VTP server mode, VLAN configurations are saved in
nonvolatile RAM. VTP server is the default mode.

VTP client

In this mode, a VTP client behaves like a VTP server, but you
cannot create, change, or delete VLANs on a VTP client.

In VTP client mode, VLAN configurations are saved in
nonvolatile RAM.

VTP transparent In this mode, VTP transparent switches do not participate in

VTP. A VTP transparent switch does not advertise its VLAN
configuration and does not synchronize its VLAN
configuration based on received advertisements. However,
transparent switches do forward VTP advertisements that
they receive from other switches. You can create, modify, and
delete VLANs on a switch in VTP transparent mode.

In VTP transparent mode, VLAN configurations are saved in
nonvolatile RAM, but they are not advertised to other
switches.

«
...
244
245
246
247
248
...
»

Summary of Contents for WS-C2950-24









































































































































































































































































































































































Reviews:

No comments

Related manuals for WS-C2950-24

Brand: 3Com Pages: 48

Brand: GE Pages: 6

BiPAC 4500NZ(L)

Brand: Billion Pages: 146

TokenLink Velocity 3C319

Brand: 3Com Pages: 2

SISPM1040-582-LRT

Brand: Lantronix Pages: 2

Brand: Lantronix Pages: 7

Maestro E220 Series

Brand: Lantronix Pages: 25

Brand: Ubiquiti Pages: 40

SMART NODE 4950-NCE

Brand: Patton electronics Pages: 8

NetLink 2960 RAS

Brand: Patton electronics Pages: 2

Brand: Patton electronics Pages: 2

Brand: Qlogic Pages: 20

Brand: A10 Pages: 52

Brand: bintec elmeg Pages: 33

MasterBus Tanklevel Interface

Brand: Mastervolt Pages: 8

Brand: Patton electronics Pages: 13

Brand: Angel Cool Pages: 2

Brand: Cowfish Technologies Pages: 38

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands