Cisco WLC 5700 Series Command Reference Manual Download Page 44 | Manualshive

Page: 44 / 82

background image

pagp port-priority

To select a port over which all Port Aggregation Protocol (PAgP) traffic through the EtherChannel is sent,
use the

pagp port-priority

command in interface configuration mode. If all unused ports in the EtherChannel

are in hot-standby mode, they can be placed into operation if the currently selected port and link fails. To
return to the default setting, use the

no

form of this command.

pagp port-priority priority

no pagp port-priority

Syntax Description

Priority number. The range is from 0 to 255.

priority

Command Default

The default is 128.

Command Modes

Interface configuration

Command History

Modification

Release

This command was introduced.

Cisco IOS XE 3.2SE

Usage Guidelines

The physical port with the highest priority that is operational and has membership in the same EtherChannel
is the one selected for PAgP transmission.

The controller supports address learning only on aggregate ports even though the

physical-port

keyword is

provided in the command-line interface (CLI). The

pagp learn-method

and the

pagp port-priority

interface

configuration commands have no effect on the controller hardware, but they are required for PAgP
interoperability with devices that only support address learning by physical ports, such as the Catalyst 1900
switch.

When the link partner to the controller is a physical learner, we recommend that you configure the controller
as a physical-port learner by using the

pagp learn-method physical-port

interface configuration command.

We also recommend that you set the load-distribution method based on the source MAC address by using the

port-channel load-balance src-mac

global configuration command. Use the

pagp learn-method

interface

configuration command only in this situation.

Examples

This example shows how to set the port priority to 200:

Controller(config-if)#

pagp port-priority 200

You can verify your setting by entering the

show running-config

privileged EXEC command or the

show

pagp channel-group-number internal

privileged EXEC command.

Layer 2/3 Command Reference, Cisco IOS XE Release 3E (Cisco WLC 5700 Series)

36

OL-32323-01

Layer 2/3 Commands

pagp port-priority

«
...
42
43
44
45
46
...
»

Summary of Contents for WLC 5700 Series



















































































Reviews:

No comments

Related manuals for WLC 5700 Series

All in One Printer

Brand: Baracoda Pages: 42

Brand: D-Link Pages: 15

DSN-4100 Series

Brand: D-Link Pages: 2

Brand: D-Link Pages: 2

Brand: Mafell Pages: 162

Brand: PaloAlto Networks Pages: 2

Brand: Teknim Pages: 10

Brand: NETGEAR Pages: 2

Brand: Patton electronics Pages: 2

Brand: Lanner Pages: 78

Brand: QuickLink Pages: 8

Brand: SurfControl Pages: 2

FieldPoint FP-3000

Brand: National Instruments Pages: 118

Brand: Cisco MERAKI Pages: 4

Brand: LevelOne Pages: 26

Mobileraid MR8X

Brand: Sans Digital Pages: 81

Brand: NetComm Pages: 75

Brand: Proscend Pages: 93

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands