Cisco VG310 Hardware Installation Manual Download Page 77

Page: 77 / 96

Environmental Specifications

Value

Description

–

4 °F to 149 °F (

–

20 °C to 65 °C)

Nonoperating
temperature

5% to 95% relative humidity

Nonoperating humidity

0 ft to 15,000 ft (0 m to 4570 m)

Nonoperating altitude

32 °F to 104 °F (0 °C to 40 °C)

Operating temperature

10% to 85% relative humidity

Operating humidity

0 ft to 10,000 ft (0 m to 3000 m)

Operating altitude

Ultimate disposal of this product should be handled according to all national laws and regulations. Statement
1040

Warning

Acoustic

Value

Description

36 dBA/65 dBA at 3 ft (91.44 cm)

Acoustic: Sound Pressure
(Typical/Maximum)

Transportation and Storage

Value

Description

–

40 °F to 158 °F (

–

40 °C to 70 °C)

Nonoperating
temperature

5% to 95%

Nonoperating humidity

15,000 ft (4570 m)

Nonoperating altitude

Cisco VG310 and Cisco VG320 Voice Gateways Hardware Installation Guide

OL-31292-01

Technical Specifications

Environmental Specifications

Summary of Contents for VG310
































































































Search results

Summary of Contents for VG310

Reviews:

Related manuals for VG310

Brands by name

Popular brands

Cisco VG310, Hardware Installation Manual

Search results

Summary of Contents for VG310

Reviews:

Related manuals for VG310

Brands by name

Popular brands