Cisco UCS 6400 Series Hardware Installation Manual Download | Manualshive

Page: 19 / 68

background image

C H A P T E R

2

Installing the Cisco UCS Fabric Interconnect

•

Preparing for Installation, on page 13

•

Cabinet and Rack Requirements, on page 15

•

Establishing System Ground, on page 21

Preparing for Installation

Considerations and Warnings

Before you install, operate, or service the system, read the

Regulatory Compliance and Safety Information

for Cisco UCS

for important safety information.

Note

IMPORTANT SAFETY INSTRUCTIONS This warning symbol means danger. You are in a situation that
could cause bodily injury. Before you work on any equipment, be aware of the hazards involved with electrical
circuitry and be familiar with standard practices for preventing accidents. Use the statement number provided
at the end of each warning to locate its translation in the translated safety warnings that accompanied this
device. Statement 1071

Warning

SAVE THESE INSTRUCTIONS

This unit is intended for installation in restricted access areas. A restricted access area can be accessed only
through the use of a special tool, lock and key, or other means of security. Statement 1017

Warning

Only trained and qualified personnel must be allowed to install, replace, or service this equipment.
Statement 1030

Warning

Cisco UCS 6400 Series Fabric Interconnect Hardware Installation Guide

13

«
...
17
18
19
20
21
...
»

Summary of Contents for UCS 6400 Series





































































Reviews:

No comments

Related manuals for UCS 6400 Series

Solid Stainless Steel Shelving

Brand: Omega Pages: 2

Brand: SanDisk Pages: 4

Brand: TrekStor Pages: 100

SO READY SECURE

Brand: DANE-ELEC Pages: 2

Brand: NEC Pages: 408

Brand: Quantum Pages: 312

Brand: GrainPro Pages: 19

Brand: AMX Pages: 2

Brand: Jung Pages: 16

Travelstar 14GS

Brand: IBM Pages: 2

DiskStation DS415play

Brand: Synology Pages: 16

Brand: B&B Electronics Pages: 2

ICPE2600 Series

Brand: 3onedata Pages: 5

Brand: EXAGATE Pages: 8

PRIMERGY BX620 S5

Brand: Fujitsu Pages: 50

PRIMERGY BX620 S4

Brand: Fujitsu Pages: 81

PRIMERGY BX900 S1

Brand: Fujitsu Pages: 46

PRIMERGY BX620 S6

Brand: Fujitsu Pages: 56

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands