manualshive.com logo in svg

Cisco uBR7200 Series, Software Configuration Manual

The Cisco uBR7200 Series, a reliable and advanced networking solution, ensures seamless connectivity. To ensure regulatory compliance and user safety, make sure to download and access the comprehensive "Regulatory Compliance And Safety Information Manual." Find it easily and for free on our website.

Share
Download
background image

1-65

Cisco uBR7200 Series Universal Broadband Router Software Configuration Guide

OL-2239-05

Chapter 1      Overview of Cisco uBR7200 Series Software

Supported Software Features for the Cisco uBR7200 Series

  •

Best effort-Data traffic sent on a non-guaranteed best-effort basis 

  •

Committed Information Rate (CIR)—Guaranteed minimum bandwidth for data traffic 

  •

Unsolicited Grants (UGS)—Constant bit rate (CBR) traffic, such as voice, that is characterized by 
fixed size packets at fixed intervals 

  •

Real Time Polling (rtPS)—Real Time service flows, such as video, that produce unicast, variable 
size packets at fixed intervals 

  •

Unsolicited Grants with Activity Detection (USG-AD)—Combination of UGS and RTPS, to 
accommodate real time traffic that might have periods of inactivity (such as voice using silence 
suppression). The service flow uses UGS fixed grants while active, but switches to RTPS polling 
during periods of inactivity to avoid wasting unused bandwidth. 

  •

Enhanced time-slot scheduling mechanisms to support guaranteed delay/jitter sensitive traffic on the 
shared multiple access upstream link

DOCSIS 1.1 Two-way Transmission (Cisco uBR7246VXR Router)

The Cisco uBR7200 series routers allow DOCSIS 1.1 two-way transmission of digital data and Voice 
over IP (VoIP) traffic over a hybrid fiber-coaxial (HFC) network. The Cisco uBR7200 series support IP 
routing with a wide variety of protocols and combinations of Ethernet, Fast Ethernet, Gigabit Ethernet, 
serial, High-Speed Serial Interface (HSSI), Packet over SONET (POS) OC-3 and OC-12c, and 
Asynchronous Transfer Mode (ATM) media.

Downstream Channel ID

This feature allows all cable modems in an HFC network to identify themselves via unique downstream 
channel IDs instead of their downstream frequencies.

To configure the downstream channel ID, use the 

cable downstream channel-id

 configuration 

command. Use the 

no

 form of this command to set the downstream channel ID to its default value. 

cable downstream channel-id 

id

no cable downstream channel-id

Syntax DescriptionS

For additional information, refer to the following documents on Cisco.com:

  •

Configuring Downstream Channel IDs

http://www.cisco.com/en/US/docs/ios/12_0t/12_0t4/feature/guide/downchan.html

  •

Cisco IOS CMTS Cable Command Reference Guide

http://www.cisco.com/en/US/docs/ios/cable/command/reference/cbl_book.html

Downstream Frequency Override

Downstream frequency override allows the CMTS administrator to change the downstream frequency 
assigned to a cable modem, overriding the frequency set in the cable modem DOCSIS configuration file.

To enable cable downstream frequency override, use the 

cable downstream override

 command in cable 

interface configuration mode. To disable the override feature, use the 

no

 form of this command.

cable downstream override

no cable downstream override

For additional command information, refer to the following document on Cisco.com:

id

 

Specifies a downstream channel ID. Valid values are from 1 to 255. 

Summary of Contents for uBR7200 Series





































































































































































































































































































































Reviews:

No comments

Related manuals for uBR7200 Series

Samsung AllShare Cast Dongle Quick Start Manual preview
AllShare Cast Dongle
Brand: Samsung Pages: 2
D-Link DSL-2750U Setup preview
DSL-2750U
Brand: D-Link Pages: 14
D-Link DVG-7022S Quick Installation Manual preview
DVG-7022S
Brand: D-Link Pages: 7
D-Link DIR-878 Quick Installation Manual preview
DIR-878
Brand: D-Link Pages: 41
D-Link Verizon DSL-2750B Setup Manual preview
Verizon DSL-2750B
Brand: D-Link Pages: 6
D-Link DIR-857 Quick Installation Manual preview
DIR-857
Brand: D-Link Pages: 10
D-Link DSL-2740U Quick Installation Manual preview
DSL-2740U
Brand: D-Link Pages: 38
Patton electronics 1090 Service Manual preview
1090
Brand: Patton electronics Pages: 8
iDirect Evolution X3 Installation And Safety Manual preview
Evolution X3
Brand: iDirect Pages: 60
Paradyne COMSPHERE 3800 Series Release Note preview
COMSPHERE 3800 Series
Brand: Paradyne Pages: 88
Paradyne COMSPHERE 3800PLUS Supplementary Manual preview
COMSPHERE 3800PLUS
Brand: Paradyne Pages: 5
Paradyne Hotwire 6212 Quick Installation Instructions preview
Hotwire 6212
Brand: Paradyne Pages: 2
Paradyne 7995-A2-374 Quick Installation Instructions preview
7995-A2-374
Brand: Paradyne Pages: 1
Intel SRCSASBB8I - RAID Controller Hardware User'S Manual preview
SRCSASBB8I - RAID Controller
Brand: Intel Pages: 36
Matrix Switch Corporation MSC-5-3232 Product Manual preview
MSC-5-3232
Brand: Matrix Switch Corporation Pages: 61
Multitech MultiConnect SE MTS2EA Quick Start Manual preview
MultiConnect SE MTS2EA
Brand: Multitech Pages: 8
Allied Telesis AT-8000C Declaration Of Conformity preview
AT-8000C
Brand: Allied Telesis Pages: 1
Acces I/O products MPCIE-ICM232-2 Hardware Manual preview
MPCIE-ICM232-2
Brand: Acces I/O products Pages: 5

Brands by name

Popular brands

Load more brands