Installing Cisco TelePresence System Profile 65”
Page 2
78-19779-02 Profile 65 Installation Sheet | April 2012 | © 2010-2012 Cisco Systems, Inc. All rights reserved.
5
Mounting the wall stand
(applies to wall stand option only)
The wall brackets, bracket spacer, and Allen key
are found in the foot module box.
10
Mounting the grilles in front and finishing up
8
Mounting the camera
1.
Open the top cover on
the monitor.
2.
Connect the camera
cable to the HDMI and
RJ45 connectors on the
camera.
9
Connect camera cables to the codec
7
Connecting the monitor cables
Locate the cables in the bottom module and connect them as described
in the illustration:
1.
HDMI cable
2.
9 pin D-SUb cable
3.
15 pin D-SUb cable
4.
Power cable
11
Connect cables on the rear side
Ethernet cable
PC cable
Microphone
cables
Power
cable
RJ45
HDMI
Mounting hole (Tripod) 1/4" UNC
Rev
S/N
2
0
0
0
0
0
0
0
0
1
1
1
V
ideo format
3
0
0
0
0
1
1
1
1
0
0
0
4
0
0
1
1
0
0
1
1
0
0
1
1
0
0
0
0
0
0
0
0
0
0
0
5
HD-SDI
0
Auto*
1 1080p25
0 1080p30
1 1080p50
0 1080p60
1 720p25
0 720p30
1 720p50
0 720p60
1 480p60
0
SW control**
1080p25
1080p30
720p50
720p60
720p25
720p30
720p50
720p60
480p60
1
0
HDMI
*Camera negotiates format over HDMI, HD-SDI tracks
HDMI, and defaults to 1080p30 in absence of HDMI sync.
**Please consult manual.
B
HDMI
RJ45
1.
Push the camera cable down the channel through the monitor.
2.
Use the two cable clamps to fasten the cable inside the bottom module.
Push the camera cable down the
channel through the Monitor.
Use the cable clamps to fasten the cable
inside the Bottom Module
and connect to the codec.
Camera cable
Camera cable goes
inside the channel.
6
Unpacking the monitor box and mounting the monitor to the base
NOTE:
Requires 4 people
and lifting straps to lift.
LIFTING STRAPS INCLUDED.
The lifting straps are found
in the box, together with the
monitor, ready for use.
NOTE:
The straps are not
fixed to the monitor. be careful
when lifting the monitor so the
straps do not slide during the
lifting operation.
CAUTION
HEAvY
AND
BULKY
REQUIRES:
4 PEOPLE TO LIfT
Set the camera DIP switch (country specific setting):
•
50 Hz: 00011, gives 1080p50 (720p50 for HD-SDI).
•
60 Hz: 00100, gives 1080p60 (720p60 for HD-SDI).
The codec is placed
inside the front door.
Choose the short or long bracket
depending on the required distance
between the bottom module and the
wall.
Use the spacer between the bottom
module and the wall bracket.
Long wall bracket
Short wall bracket
Spacer
Connect the microphone cables to the
Microphone connectors on the codec.
Connect the HDMI cable to the
HDMI 1 input at the codec.
Connect the 9 pin D-SUb cable
to the Camera control input at the
codec.
WARNING
Due to the size and mass of this equipment,
it is very important that the wall stand is
safely installed according to the installation
instructions, and that the wall is able to safely
support the product.
It is highly recommended that the wall stand is
installed by trained personnel.
1.
Choose the short or long bracket depending
on the required distance between the
bottom module and the wall.
2.
Place the spacer underneath the wall
bracket and fasten the bracket to the bottom
module. Re-use the existing three screws.
Use the Allen key, found in the foot module
box.
3.
Place the bottom module by the wall, mark
where to fasten the bracket and move away
the bottom module.
4.
Add the suitable fixing device for the screws
in the wall.
5.
Connect the the cables (see step 11) and
lead them out at the back before fastening
the unit to the wall.
6.
Place the bottom module by the wall and
fasten it to the wall.
3.
Hold the camera
upside down and
carefully slide the
camera into place.
3.
Connect the camera cables:
1.
Close the top cover.
2.
Snap on the top grille.
3.
Snap on the speaker grille.
4.
Remove the plastic foil on the monitor frame.
5.
Use the supplied cloth to clean up the system.
1.
Locate and connect the cables
which are lead out of the system
at the rear side:
•
Ethernet cable
•
PC cable
•
Microphone cables
•
Power cable
2.
Follow the instructions in
the accompanying Touch 8”
installation guide to connect and
initialize the touch interface device.
EMC Class A declaration
WARNING:
This is a class A product. In a domestic environment this product may cause radio
interference in which case the user may be required to take adequate measures.
A
级声明
(A Class product declaration)
本产品为
A
级
ITE
,在其使用说明,铭牌等显著位置中已包含如下内容的声明
(We declare here that the subject product is A class ITE product, and the
following statement is clearly marked in the user manual or nameplate):
声明所在位置
(Position of the Declaration):
使用说明
User Manual
铭牌
Nameplate
申请号
(Application No.)
:
申请人
(Applicant):
型号
(Model Number)
:
签字
/
盖章
Signature/Stamp:
日期
Date:
警告
此为
A
级产品。在生活环境中,该产品可能会造成无线电干扰。在这种
情况下,可能需要用户对干扰采取切实可行的措施。
WARNING:
This is a class A product. In a domestic environment this
product may cause radio interference in which case the user may be
required to take adequate measures.