background image

Connecting the Cisco Network Interface Module Adapter for SM-X Slot on the Cisco 4000 Seris Integrated Services 

5

Connecting the Cisco Network Interface Module Adapter for SM-X Slot on Cisco 4300 and 4400 Series Integrated Services Routers

Warning

Read the installation instructions before connecting the system to the power source. 

Statement 1004

Warning

This unit might have more than one power supply connection. All connections must be removed to 
de-energize the unit. 

Statement 1028

Warning

Only trained and qualified personnel should be allowed to install, replace, or service this equipment. 

Statement 1030

Warning

Do not use this product near water; for example, near a bath tub, wash bowl, kitchen sink or laundry 
tub, in a wet basement, or near a swimming pool. 

Statement 1035

Warning

Never install telephone jacks in wet locations unless the jack is specifically designed for 
wet locations. 

Statement 1036

Warning

Never touch uninsulated telephone wires or terminals unless the telephone line has been 
disconnected at the network interface. 

Statement 1037

Warning

Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a remote 
risk of electric shock from lightning. 

Statement 1038

Warning

To report a gas leak, do not use a telephone in the vicinity of the leak. 

Statement 1039

Warning

Ultimate disposal of this product should be handled according to all national laws and regulations. 

Statement 1040

Warning

When installing or replacing the unit, the ground connection must always be made first and 
disconnected last. 

Statement 1046

The following warnings apply in Australia:

Warning

Before working on equipment that is connected to power lines, remove jewelry (including rings, 
necklaces, and watches). Metal objects will heat up when connected to power and ground and can 
cause serious burns or weld the metal object to the terminals. 

Statement 43

Summary of Contents for SM-X-NIM-ADPTR











Reviews: