Cisco SE680 WiMAX User Manual Download Page 11 | Manualshive

Page: 11 / 67

background image

11

System requirements

SE680 WiMAX / engbt / SE680_FUG_EN-7 / Installation.fm / 13.5.11

Schablo

ne 201

1_04

_07

Choosing the location



Choose the location so that you can easily establish the following connections:
– Ethernet cable socket, which, for example, establishes the connection to the out-

door modem through a wall duct.

– Ethernet cable socket for connection with a PC or network.
– Connection of the power lead with a mains socket.



First choose the location for the indoor unit:
– Consider the stated temperature range for the indoor unit when choosing the

location (see "Specifications" on page 46).



The indoor unit can be operated either on a horizontal surface or mounted on a wall.
Make sure the connections cannot become loose and that the LEDs are clearly vis-
ible.



Lay the cables in such a way that nobody can tread on or trip over them.

System requirements

To install and get started with the indoor unit, the following requirements must be ful-
filled:



The outdoor modem has been properly installed and is ready for use. The associ-
ated Ethernet cable is fitted with an RJ45 plug and ends close to the indoor unit.



PC with a LAN interface 10/100BaseT

or

an Ethernet network

10/100BaseT. The network adapter must support one of the following modes:
10BaseT Half Duplex, 10BaseT Full Duplex, 100BaseT Half Duplex,
100BaseT Full Duplex.



The TCP/IP protocol has to be set up on the PC (standard installation for Windows
XP and Windows Vista; if you are using a different Windows operating system, read
the separate instructions on network configuration on the product CD, if necessary).

Wall mounting (optional)

The indoor unit is fitted with two clips for wall mounting. Wall mounting is not absolutely
necessary, but is recommended to make the cable connections mechanically secure.



Use screws, anchor fittings and cable clamps to mount the indoor unit on a wall.
Make sure the LEDs are easily visible.

«
...
9
10
11
12
13
...
»

Summary of Contents for SE680 WiMAX




































































Reviews:

No comments

Related manuals for SE680 WiMAX

Brand: Paradyne Pages: 58

COMSPHERE 3920PLUS Series

Brand: Paradyne Pages: 24

COMSPHERE 3920PLUS Series

Brand: Paradyne Pages: 2

Brand: Paradyne Pages: 4

Brand: Paradyne Pages: 46

COMSPHERE 3825Plus

Brand: Paradyne Pages: 20

COMSPHERE 3920PLUS Series

Brand: Paradyne Pages: 3

Brand: Paradyne Pages: 34

COMSPHERE 6700 Series

Brand: Paradyne Pages: 3

Brand: Paradyne Pages: 28

COMSPHERE 3825Plus

Brand: Paradyne Pages: 1

Brand: Sagem Pages: 4

Brand: WaveRider Pages: 44

Brand: Sel Pages: 16

Brand: Comtrend Corporation Pages: 10

Brand: NextNet Pages: 26

Brand: Aztech Pages: 3

Brand: Commander Pages: 5

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands