manualshive.com logo in svg

Cisco PA-MC-T3, Installing And Removing

Share
Download
Cisco PA-MC-T3 Installing And Removing Download Page 4

3-4

PA-MC-T3 Port Adapter Installation and Configuration

OL-2695-05

Chapter 3      Removing and Installing Port Adapters

  Port Adapter Removal and Installation

Port Adapter Removal and Installation 

In this section, the illustrations that follow give step-by-step instructions on how to remove and install 
port adapters. This section contains the following illustrations:

•

Catalyst RSM/VIP2—Removing and Installing a Port Adapter, page 3-5

•

FlexWAN Module—Removing and Installing a Port Adapter, page 3-6

•

Cisco 7200 Series Routers and Cisco 7200 VXR Routers—Removing and Installing a Port Adapter, 
page 3-7

•

Cisco uBR7200 Series Routers—Removing a Port Adapter, page 3-8

 

•

Cisco uBR7200 Series Routers—Installing a Port Adapter, page 3-9

 

•

Cisco 7201 Router—Removing and Installing a Port Adapter, page 3-10

•

Cisco 7301 Router—Removing and Installing a Port Adapter, page 3-11

•

Cisco 7304 PCI Port Adapter Carrier Card—Removing and Installing a Port Adapter, page 3-12

•

Cisco 7401ASR Router—Removing and Installing a Port Adapter, page 3-14

•

VIP—Removing and Installing a Port Adapter, page 3-15

Note

The PA-MC-T3 port adapter can be installed in port adapter slots 0 or 1 on the Catalyst RSM/VIP2 
motherboard, the Catalyst 6000 family FlexWAN module, or the VIP and in any available port adapter 
slot in all other systems.

Caution

Each port adapter circuit board is mounted to a metal carrier and is sensitive to electrostatic discharge 
(ESD) damage.

Warning

During this procedure, wear grounding wrist straps to avoid ESD damage to the card. Do not directly 
touch the midplane with your hand or any metal tool, or you could shock yourself. 

Statement 181

Tip

If a port adapter lever or other retaining mechanism does not move to the locked position, the port 
adapter is not completely seated in the midplane. Carefully pull the port adapter halfway out of the slot, 
reinsert it, and move the port adapter lever or other mechanism to the locked position.

Caution

To prevent jamming the carrier between the upper and the lower edges of the port adapter slot, and to 
ensure that the edge connector at the rear of the port adapter mates with the connection at the rear of the 
port adapter slot, make certain that the carrier is positioned correctly, as shown in the cutaway in the 
following illustrations.

Summary of Contents for PA-MC-T3



















Reviews:

No comments

Brands by name

Popular brands

Load more brands