background image

3-3

PA-4R-DTR Dedicated Token Ring Port Adapter Installation and Configuration

OL3590-02

Chapter 3      Removing and Installing Port Adapters

  Warnings and Cautions

Specifically, when you insert a module, the longest pins make contact with the module first, and the 
shortest pins make contact last. The system recognizes the signals and the sequence in which it receives 
them.

When you remove or insert a module, the pins send signals to notify the system of changes. The router 
then perfoms the following procedure:

1.

Rapidly scans the system for configuration changes.

2.

Initializes newly inserted port adapters or administratively shuts down any vacant interfaces.

3.

Brings all previously configured interfaces on the module back to their previously installed state. 
Any newly inserted interface is put in the administratively shutdown state, as if it was present (but 
not configured) at boot time. If a similar module type is reinserted into a slot, its ports are configured 
and brought online up to the port count of the originally installed module of that type. 

Note

Before you begin installation, read 

Chapter 2, “Preparing for Installation,”

 for a list of parts and tools 

required for installation.

Warnings and Cautions

Observe the following warnings and cautions when installing or removing port adapters.

Caution

Do not slide a port adapter all the way into the slot until you have connected all required cables. Trying 
to do so disrupts normal operation of the router or switch.

Note

If a port adapter lever or other retaining mechanism does not move to the locked position, the port 
adapter is not completely seated in the midplane. Carefully pull the port adapter halfway out of the slot, 
reinsert it, and move the port adapter lever or other mechanism to the locked position.

Caution

To prevent jamming the carrier between the upper and the lower edges of the port adapter slot, and to 
ensure that the edge connector at the rear of the port adapter mates with the connection at the rear of the 
port adapter slot, make certain that the carrier is positioned correctly, as shown in the cutaway in the 
following illustrations.

Warning

When performing the following procedures, wear a grounding wrist strap to avoid ESD damage to the 
card. Some platforms have an ESD connector for attaching the wrist strap. Do not directly touch the 
midplane or backplane with your hand or any metal tool, or you could shock yourself.

Port Adapter Removal and Installation

In this section, the illustrations that follow give step-by-step instructions on how to remove and install 
port adapters. This section contains the following illustrations:

Cisco 7100 Series—Removing and Installing a Port Adapter, page 3-5

Summary of Contents for PA-4R-DTR

















































Reviews: