background image

 

12

PA-2JT2 6.3-MHz Serial Port Adapter Installation and Configuration

OL-3587-01

VIP2 and the JT2 Port Adapter

Note

Time slots 1 to 96 are used for the data payload, while time slots 97 and 98 are used for maintenance 
signaling by the DSU, the terminal equipment (TE), the network termination equipment (NT), or the line 
termination equipment (LT).

The last five bits of the frame, bit 785 through bit 789, are called the F-bits. The F-bits contain the frame 
and multiframe alignment signal, which consists of nine bits (110010100) carried in the first two frames 
of the multiframe.

VIP2 and the JT2 Port Adapter

This section describes the JT2 port adapter and its use with the VIP2.

The following sections provide additional information specific to the JT2 port adapter and its use on the 
VIP2 in Cisco 7000 series and Cisco 7500 series routers:

Installing or Replacing a Port Adapter on a VIP2, page 13

Attaching JT2 Port Adapter Interface Cables, page 14

Configuring the JT2 Interfaces, page 16

 shows a VIP2-40 with two JT2 port adapters in port adapter slots 0 and 1. Port adapters can be installed 
in either (or both) port adapter slot 0 or port adapter slot 1. You can install VIP2s in any interface 
processor slots in your Cisco 7500 series or Cisco 7000 series router.

Figure 7

VIP2-40 with Two JT2 Port Adapters (Horizontal Orientation Shown)

H9370

EN

AB

LE

D

AIS RAI LOS

AIS RAI LOS

JT2

TX0

RX0

TX1

RX1

PA-2JT2 in 

port adapter

slot 0

PA-2JT2 in 
port adapter 
slot 1

Port adapter
handles not
shown

Bus connector

DRAM

SIMMs

SRAM

DIMM U5

CPU

U6

U2

U4

Boot ROM

EN

AB

LE

D

AIS RAI LOS

AIS RAI

JT2

TX0

RX0

TX1

RX1

AIS RAI LOS

Summary of Contents for PA-2JT2





























Reviews: