manualshive.com logo in svg

Cisco PA-2FEISL-FX, Installation And Configuration Manual

Share
Download
Cisco PA-2FEISL-FX Installation And Configuration Manual Download Page 42

3-10

PA-2FEISL 100BASE-T Fast Ethernet/ISL Port Adapter Installation and Configuration

OL-3475-02

Chapter 3      Removing and Installing Port Adapters

  Connecting a PA-2FEISL RJ-45 or SC Cable

Connecting a PA-2FEISL RJ-45 or SC Cable

To continue your PA-2FEISL port adapter installation, you must install the port adapter’s interface 
cables. The following instructions apply to all supported platforms. 

RJ-45 and SC-type fiber optic cables are not available from Cisco; they are available from commercial 
cable vendors.

Use the following procedure to connect

 

RJ-45 or SC cables:

Step 1

If you have RJ-45 connections (PA-2FEISL-TX), attach the Category 5 unshielded twisted-pair (UTP) 
cable directly to an RJ-45 port on the PA-2FEISL-TX. See (

Figure 3-2

.) The PA-2FEISL is an end station 

device and not a repeater. You 

must

 connect the PA-2FEISL to a repeater, hub, or back-to-back to another 

100-Mbps Fast Ethernet adapter.

If you have SC connections (PA-2FEISL-FX), attach the cable directly to an SC port on the 
PA-2FEISL-FX. See (

Figure 3-3

.) Use either one duplex SC connector or two simplex SC connectors, 

and observe the correct relationship between the receive (RX) and transmit (TX) ports on the 
PA-2FEISL-FX and your repeater.

Note

Port adapters have a handle attached, but this handle is not shown to allow a full detailed view 
of each port adapter’s faceplate.

Figure 3-2

Connecting a PA-2FEISL-TX RJ-45 Cable—Horizontal Orientation (Shown Without 
Handles)

10992

To repeater

or DTE

RJ-45 cable

To repeater

or DTE

RJ-45 cable

FAST ETHERNET/ISL

LI

N

K

LI

N

K

EN

AB

LE

D

0

1

Summary of Contents for PA-2FEISL-FX



























































Reviews:

No comments

Brands by name

Popular brands

Load more brands