Cisco ONS 15454 Hardware Installation Manual Download Page 471

Page: 471 / 516

Figure 291: Replacing the Air Filter

Step 4

Replace the air filter with a new one if the air filter is dirty or clogged with dust.

Step 5

Attach the cable guide and insert the air filter into the shelf assembly.

The air filter must be inserted with the grid facing the shelf assembly as shown in

Figure 291:

Replacing the Air Filter, on page 441

Note

Step 6

Tighten the screw on the air-filter.

Stop. You have completed this procedure.

NTP-G262 Replace the Air Filter of the ONS 15454 M6 Shelf
Assembly

This procedure replaces the air filter of the ONS 15454 M6 shelf assembly.

Purpose

New air filter

Tools/Equipment

•

NTP-G252 Install the ONS 15454 M6 Shelf , on page 294

• Connect the chassis to the office ground. For detailed instructions on how

to ground the chassis, refer to the

Electrostatic Discharge and Grounding

Guide for Cisco CPT and Cisco ONS Platforms

Prerequisite Procedures

As Needed

Required/As Needed

Remote

Onsite/Remote

Provisioning or higher

Security Level

Cisco ONS 15454 Hardware Installation Guide

441

Maintaining the ONS 15454 M12 (ANSI and ETSI), ONS 15454 M2 and ONS 15454 M6 Shelf

NTP-G262 Replace the Air Filter of the ONS 15454 M6 Shelf Assembly

Summary of Contents for ONS 15454




































































































































































































































































































































































































































































































































Search results

Summary of Contents for ONS 15454

Reviews:

Related manuals for ONS 15454

Brands by name

Popular brands

Cisco ONS 15454, Hardware Installation Manual

Search results

Summary of Contents for ONS 15454

Reviews:

Related manuals for ONS 15454

Brands by name

Popular brands