Cisco ONS 15454 M6 Maintenance Manual Download | Manualshive

Page: 7 / 32

background image

Figure 5: Replacing the Air Filter

Step 4

Replace the air filter with a new one if the air filter is dirty or clogged with dust.

Step 5

Attach the cable guide and insert the air filter into the shelf assembly.

The air filter must be inserted with the grid facing the shelf assembly as shown in

Figure 5: Replacing

the Air Filter, on page 7

.

Note

Step 6

Tighten the screw on the air-filter.

Stop. You have completed this procedure.

NTP-G262 Replace the Air Filter of the ONS 15454 M6 Shelf
Assembly

This procedure replaces the air filter of the ONS 15454 M6 shelf assembly.

Purpose

New air filter

Tools/Equipment

•

NTP-G252 Install the ONS 15454 M6 Shelf

• Connect the chassis to the office ground. For detailed instructions on how

to ground the chassis, refer to the

Electrostatic Discharge and Grounding

Guide for Cisco CPT and Cisco ONS Platforms

.

Prerequisite Procedures

As Needed

Required/As Needed

Remote

Onsite/Remote

Provisioning or higher

Security Level

Maintaining the ONS 15454 M12 (ANSI and ETSI), ONS 15454 M2 and ONS 15454 M6 Shelf

7

Maintaining the ONS 15454 M12 (ANSI and ETSI), ONS 15454 M2 and ONS 15454 M6 Shelf

NTP-G262 Replace the Air Filter of the ONS 15454 M6 Shelf Assembly

«
...
5
6
7
8
9
...
»

Summary of Contents for ONS 15454 M6

































Reviews:

No comments

Related manuals for ONS 15454 M6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands