Cisco ONS 15454 M6 Installation Manual Download | Manualshive

Page: 2 / 164

background image

•

NTP-G312 Attach Wires to Alarm, Timing, LAN, and Craft Pin Connections in Cisco ONS 15454 M6,
on page 127

•

NTP-G308 Connect the ONS 15454 M6 Multishelf Node and the ONS 15454 M6 Subtending Shelves,
on page 137

•

NTP-G309 Connect the ONS 15454 M6 and the ONS 15454 in a Mixed Multishelf Configuration, on
page 139

•

NTP-G310 Upgrade the ONS 15454 Multishelf Configuration Using the ONS 15454 M6 , on page 149

•

NTP-G264 Perform the ONS 15454 M6 Shelf Installation Acceptance Test , on page 155

•

NTP-G317 Connect the ONS 15454 M6 Multishelf Node and the ONS 15454 M6 Subtending Shelves
with Simplex Controllers, on page 158

•

NTP-G318 Connect the ONS 15454 M6 Multishelf Node and the ONS 15454 M6 Subtending Shelves
in a Ring Topology, on page 160

•

Air Deflector, on page 161

•

Filler and Blank Cards, on page 162

•

Air Filter , on page 162

•

Shelf Voltage and Temperature, on page 163

•

Cooling Profile, on page 163

ANSI Rack Installation

The ONS 15454 M6 shelf is mounted on a 19-inch (482.6-mm) or 23-inch (584.2-mm) equipment rack. Make
sure that the correct type of 19-inch ANSI rack is used for mounting the ONS 15454 M6 shelf as shown in

. If the shelf is mounted in the front position, then it projects 1.7 inches (43.18 mm) from the front

of the rack. If the shelf is mounted in the middle position, then it projects 5.1 inches (129.54 mm) from the
front of the rack. The shelf mounts in both Electronic Industries Alliance (EIA) standard and Telcordia-standard
racks. The shelf is a total of 17 inches (431.8 mm) wide with no mounting ears attached. Ring runs are not
provided by Cisco and might hinder side-by-side installation of shelves where space is limited.

The ONS 15454 M6 shelf measures 10.4 inches (264.16 mm) high, 19 or 23 inches (482.6 or 584.2 mm) wide
(depending on which way the mounting ears are attached), and 11.1 inches (304.8 mm) deep. You can install
up to seven ONS 15454 M6 shelves in a 7-foot (2133.6 mm) equipment rack.

The following figure shows the dimensions of the ONS 15454 M6 shelf on a 19-inch (482.6 mm) ANSI rack
configuration with brackets mounted in the front position.

Installing the ONS 15454 M6 Shelf

2

Installing the ONS 15454 M6 Shelf

ANSI Rack Installation

«
1
2
3
4
...
»

Summary of Contents for ONS 15454 M6





































































































































































Reviews:

No comments

Related manuals for ONS 15454 M6

SureCross FlexPower DX99 Series

Brand: Banner Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands