Cisco ONS 15454 M6 Installation Manual Download | Manualshive

Page: 160 / 164

background image

NTP-G318 Connect the ONS 15454 M6 Multishelf Node and the
ONS 15454 M6 Subtending Shelves in a Ring Topology

Use this procedure to connect the ONS 15454 M6 multishelf node and the ONS
15454 M6 subtending shelves in a ring topology.

Purpose

Cross-over (CAT-5) LAN cables

Tools/Equipment

NTP-G313 Install and Configure the TNC, TNCE, TSC, or TSCE Card. See the
Cisco ONS 15454 DWDM Configuration Guide.

Prerequisite Procedures

As needed

Required/As Needed

Onsite

Onsite/Remote

None

Security Level

The MSM (multishelf management) ports are present on the ECU module. The MSM ports located on the left
side of the ECU module correspond to the TNC/TNCE/TSC/TSCE card in Slot 1, and the MSM ports located
on the right side correspond to the TNC/TNCE/TSC/TSCE card in Slot 8. For more information about the
ECU module and MSM ports, see the

External Connection Units, on page 72

Note

Procedure

Step 1

Using a cross-over (CAT-5) LAN cable:

a) Plug one connector into the MSM port that corresponds to the TNC/TNCE/TSC/TSCE card in Slot 1 of

the ONS 15454 M6 shelf used as the node controller.

b) Plug the other connector into the MSM port that corresponds to the TNC/TNCE/TSC/TSCE card in Slot

1 of the ONS 15454 M6 shelf used as subtending shelf.

When connecting two shelves using the cross-over cables, it is possible to have shelves not
having controller cards in same slots. Use corresponding MSM ports according to the controller
card slots.

Note

Step 2

Using a cross-over (CAT-5) LAN cable:

a) Plug one connector to any one of the remaining MSM ports of the ONS 15454 M6 SSCs in the first layer.
b) Plug the other connector to any one of the MSM ports of the ONS 15454 M6 SSCs in the next layer.
c) Repeat a and b to connect the remaining MSM ports of the ONS 15454 M6 SSCs.

After connecting all the SSCs as per Step 2, connect the last 15454 M6 SSC to the 15454 M6 node
controller to complete the ring.

You can connect up to a maximum of 9 SSCs in the ring topology.

Note

Installing the ONS 15454 M6 Shelf

160

Installing the ONS 15454 M6 Shelf

NTP-G318 Connect the ONS 15454 M6 Multishelf Node and the ONS 15454 M6 Subtending Shelves in a Ring Topology

«
...
158
159
160
161
162
...
»

Summary of Contents for ONS 15454 M6





































































































































































Reviews:

No comments

Related manuals for ONS 15454 M6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands