Cisco ONS 15454 M6 Installation Manual Download | Manualshive

Page: 118 / 164

background image

Fan Speed

The fan speed is controlled by the TNC, TNCE, TSC, or TSCE card temperature sensors. The sensors measure
the input air temperature at the fan-tray assembly. Fan speed options are low, medium, and high. If the TNC,
TNCE, TSC, or TSCE card fails, the fans automatically shift to high speed. The temperature that the TNC,
TNCE, TSC, or TSCE sensors measure appear on the LCD screen.

Fan Failure

If one or more fans fail on the fan-tray assembly, replace the entire assembly. You cannot replace individual
fans. The red Fan Fail LED on the front of the fan-tray illuminates when one or more fans fail. The red Fan
Fail LED clears after you install a working fan-tray.

NTP-G257 Install the Fan-Tray Assembly in the ONS 15454 M6
Shelf

This procedure installs the 15454-M6-FTA or 15454-M6-FTA2 fan-tray assembly
in the ONS 15454 M6 system.

Purpose

Small slot-head screwdriver

Tools/Equipment

•

NTP-G252 Install the ONS 15454 M6 Shelf , on page 24

.

•

NTP-G259 Open and Remove the Standard Door of the ONS 15454 M6
Shelf , on page 57

• Connect the chassis to the office ground. For detailed instructions on how

to ground the chassis, see the

Electrostatic Discharge and Grounding Guide

for Cisco CPT and Cisco ONS Platforms

Prerequisite Procedures

Required

Required/As Needed

Onsite

Onsite/Remote

None

Security Level

The 15454-M2-FTA2 is compatible with R9.2.0 and later releases.

Note

Do not operate an ONS 15454 M6 without an air filter. For information on the air filter, see

NTP-G114 Inspect

and Replace the Air Filter

Caution

Do not force a fan-tray assembly into place. Doing so can damage either the connectors on the fan tray or the
connectors on the backpanel of the shelf, or both.

Caution

Installing the ONS 15454 M6 Shelf

118

Installing the ONS 15454 M6 Shelf

Fan Speed

«
...
116
117
118
119
120
...
»

Summary of Contents for ONS 15454 M6





































































































































































Reviews:

No comments

Related manuals for ONS 15454 M6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands