Cisco ONS 15327 User Documentation Download | Manualshive

Page: 321 / 559

background image

9-29

Cisco ONS 15327 User Documentation, R3.3

June 2002

Chapter 9 Ethernet Operation

Spanning Tree (IEEE 802.1D)

Note

Green represents forwarding spans and purple represents blocked (protect) spans. If you have a packet
ring configuration, at least one span should be purple.

9.6.5 Ethernet Performance Screen

CTC provides Ethernet performance information that includes line-level parameters, the amount of port
bandwidth used, and historical Ethernet statistics.

9.6.5.1 Statistics Window

The Ethernet statistics screen lists Ethernet parameters at the line level.

defines the parameters.

Display the CTC card view for the Ethernet card and click the

Performance > Statistics

tabs to display

the screen.

The Baseline button resets the values on the Statistics tab to zero. The Refresh button manually refreshes
statistics. Auto-Refresh

sets a time interval for automatic refresh of statistics to occur.

Table 9-7

Ethernet Parameters

Parameter

Meaning

Link Status

Indicates whether or not link integrity is present; up means present, and
down means not present.

Rx Packets

Number of packets received since the last counter reset.

Rx Bytes

Number of bytes received since the last counter reset.

Tx Packets

Number of packets transmitted since the last counter reset.

Tx Bytes

Number of bytes transmitted since the last counter reset.

Rx Total Errors

Total number of receive errors.

Rx FCS

Number of packets with a frame check sequence (FCS) error. FCS
errors indicate frame corruption during transmission.

Rx Alignment

Number of packets with alignment errors; alignment errors are
received incomplete frames.

Rx Runts

Number of packets received that are less than 64 bytes in length.

Rx Giants

Number of packets received that are greater than 1518 bytes in length
for untagged interfaces and 1522 bytes for tagged interfaces.

Tx Collisions

Number of transmit packets that are collisions; the port and the
attached device transmitting at the same time caused collisions.

Tx Excessive

Number of consecutive collisions.

Tx Deferred

Number of packets deferred.

«
...
319
320
321
322
323
...
»

Summary of Contents for ONS 15327
















































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ONS 15327

Brand: F5 Pages: 30

Brand: Ceragon Pages: 52

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands