Cisco o UCS X440p Installation And Service Manual Download Page 54

Page: 54 / 62

Step 10

Detach the PCB from the sheetmetal and dispose of the PCB, components, and sheetmetal in compliance with relevant
e-waste and recycling laws.

What to do next

If you have not already done so, recycle the riser cage PCBAs. See:

•

Recycling the Riser A PCBA, on page 46

•

Recycling the Riser B PCBA, on page 47

Recycling the Riser A PCBA

Use the following task to disassemble the PCB for Riser Type A.

Before you begin

For Recyclers Only!

This procedure is not a standard field-service option. This procedure is for recyclers

who will be reclaiming the electronics and sheet metal for proper disposal to comply with local eco
design and e-waste regulations.

Note

To remove Riser A's PCBA, the following requirements must be met:

• The PCIe node must be disconnected from facility power.

• The chassis must be removed from the equipment rack.

Cisco UCS X440p PCIe Node Installation and Service Guide

Servicing the Cisco UCS X440p PCIe Node

Recycling the Riser A PCBA

Summary of Contents for o UCS X440p






























































Search results

Summary of Contents for o UCS X440p

Reviews:

Related manuals for o UCS X440p

Brands by name

Popular brands

Cisco o UCS X440p, Installation And Service Manual

Search results

Summary of Contents for o UCS X440p

Reviews:

Related manuals for o UCS X440p

Brands by name

Popular brands