Cisco Nexus 3400 Series Hardware Installation Manual Download Page 22

Page: 22 / 72

b) Align the two rear rack-mount guides on either side of the switch with the slider rails installed in the rack. Slide the

rack-mount guides onto the slider rails, and then gently slide the switch all the way into the rack until the front
rack-mount brackets come in contact with two rack or cabinet posts.

c) Holding the chassis level, insert screws (12-24 or 10-32, depending on the rack type) in each of the two front rack-mount

brackets (using a total of six screws) and into the cage nuts or threaded holes in the vertical rack-mounting rails (see
the following figure).

d) Tighten the 10-32 screws to 20 in-lb (2.26 N·m) or tighten the 12-24 screws to 30 in-lb (3.39 N·m).

Step 5

If you attached a grounding wire to the chassis grounding pad, connect the other end of the wire to the facility ground.

Cisco Nexus 3400 Hardware Installation Guide

Installing the Chassis

Installing the Switch Using the NXK-ACC-KIT-1RU Rack-Mount Kit

Summary of Contents for Nexus 3400 Series









































































Search results

Summary of Contents for Nexus 3400 Series

Reviews:

Related manuals for Nexus 3400 Series

Brands by name

Popular brands

Cisco Nexus 3400 Series, Hardware Installation Manual

Search results

Summary of Contents for Nexus 3400 Series

Reviews:

Related manuals for Nexus 3400 Series

Brands by name

Popular brands