manualshive.com logo in svg

Cisco NCS 2000 series, Troubleshooting Manual

The Cisco NCS 2000 series Troubleshooting Manual is an essential resource for users seeking to resolve technical issues with ease. Download this comprehensive manual for free from manualshive.com, providing step-by-step guidance and expert insights to keep your Cisco NCS 2000 series product running smoothly.

Share
Download
background image

High-performance devices on this card can get hot during operation. To remove the card, hold it by the
faceplate and bottom edge. Allow the card to cool before touching any other part of it or before placing
it in an antistatic bag.

Statement 201

Warning

Removing a card that currently carries traffic on one or more ports can cause a traffic hit. To avoid this, perform
an external switch if a switch has not already occurred. Refer to the procedures in the

Protection Switching,

Lock Initiation, and Clearing, on page 443

.

Caution

Step 2

Resend test traffic on the loopback circuit with a known-good card installed.

Step 3

If the test set indicates no errors, the problem was probably the defective card. Return the defective card to Cisco through
the RMA process. Contact Cisco Technical Support 1 800 553 2447.

Step 4

Clear the facility loopback on the port:

a) Click the

Maintenance > Loopback

tabs.

b) Choose

None

from the Loopback Type column for the port being tested.

c) Choose the appropriate state to place the port in service, out of service and disabled, out of service for maintenance,

or automatically in service from the Admin State column for the port being tested.

d) Click

Apply.

e) Click

Yes

in the confirmation dialog box.

Step 5

Complete the

Perform a Terminal Loopback on a Destination-Node MXP, TXP, XP, or ADM-10G Port, on page 24

.

Perform a Terminal Loopback on a Destination-Node MXP, TXP, XP, or
ADM-10G Port

The terminal loopback at the destination-node port is the final local hardware error elimination in the circuit
troubleshooting process. If this test is completed successfully, you have verified that the circuit is good up to
the destination port. The example in

Figure 8: Terminal Loopback on a Destination-Node MXP or TXP Port,

on page 24

shows a terminal loopback on an destination node TXP port.

Figure 8: Terminal Loopback on a Destination-Node MXP or TXP Port

Performing a loopback on an in-service circuit is service-affecting.

Caution

Cisco NCS 2000 series Troubleshooting Guide, Release 11.0

24

General Troubleshooting

Perform a Terminal Loopback on a Destination-Node MXP, TXP, XP, or ADM-10G Port

Summary of Contents for NCS 2000 series



























































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for NCS 2000 series

GE MDS SD Series Setup Manual preview
MDS SD Series
Brand: GE Pages: 4
NEC Univerge SV9300 Migration Manual preview
Univerge SV9300
Brand: NEC Pages: 26
NEC NEAX 2400 Quick Reference Manual preview
NEAX 2400
Brand: NEC Pages: 20
NEC DS2000 IntraMail Instructions preview
DS2000 IntraMail
Brand: NEC Pages: 2
3Com 3C3FE574BT Quick Start Manual preview
3C3FE574BT
Brand: 3Com Pages: 8
Tyco Electronics 8 Port 10/100Mbit/s Ethernet Smart Switch with Fibre Uplink Product User Manual preview
8 Port 10/100Mbit/s Ethernet Smart Switch with Fibre Uplink
Brand: Tyco Electronics Pages: 18
Allnet ALL1682504 Quick Installation preview
ALL1682504
Brand: Allnet Pages: 12
Telebyte 458-LM-E2-36 Quick Start Manual preview
458-LM-E2-36
Brand: Telebyte Pages: 19
ZALMAN ZM-WB2 Gold User Manual preview
ZM-WB2 Gold
Brand: ZALMAN Pages: 9
NETGEAR RP614 v2 Installation Manual preview
RP614 v2
Brand: NETGEAR Pages: 2
EVOC 6336-STG-YX Manual preview
6336-STG-YX
Brand: EVOC Pages: 57
WolfPack 18x18 Card Cage User Manual preview
18x18 Card Cage
Brand: WolfPack Pages: 31
Arduino ABX00061 Reference Manual preview
ABX00061
Brand: Arduino Pages: 25
Divio SRA311-008P8 Series Installation Manual preview
SRA311-008P8 Series
Brand: Divio Pages: 4
Promise Technology VTrak J310S Quick Start Manual preview
VTrak J310S
Brand: Promise Technology Pages: 26
Solwise 3GWIFIMRD User Manual preview
3GWIFIMRD
Brand: Solwise Pages: 231
ICP Chapter C Quick Setup Manual preview
Chapter C
Brand: ICP Pages: 68
CopperOptics 150-1342-01 Manual preview
150-1342-01
Brand: CopperOptics Pages: 12

Brands by name

Popular brands

Load more brands