Cisco N9K-C93360YC-FX2 Hardware Installation Manual Download Page 23

Page: 23 / 72

C H A P T E R

Installing the Chassis

•

Installation Options with Rack-Mount Kits, on page 15

•

Install a Rack, on page 16

•

Unpacking and Inspecting a New Switch, on page 16

•

Planning How to Position the Chassis in the Rack, on page 17

•

Installing the Chassis in a Two-Post Rack, on page 18

•

Installing the Chassis in a Four-Post Rack, on page 21

•

Installing the Airflow Vent NXA-ACC-BAV4, on page 31

•

Grounding the Chassis, on page 32

•

Starting the Switch, on page 33

Installation Options with Rack-Mount Kits

The rack-mount kit enables you to install the switch into racks of varying depths. You can position the switch
with easy access to either the port connections or the fan and power supply modules.

You can install the switch using the following rack-mount options:

• Rack-mount kit (NXK-ACC-RMK-2RU) which you can order from Cisco. This option offers you easy

installation, greater stability, increased weight capacity, added accessibility, and improved removability
with front and rear removal.

For four post racks.

• Rack-mount kit (N9K-C9300-RMK) which you can order from Cisco.

For four post racks.

The rack or cabinet that you use must meet the requirements listed the in

General Requirements for Cabinets

and Racks, on page 51

section.

You are responsible for verifying that your rack and rack-mount hardware comply with the guidelines that
are described in this doc.

Note

Cisco Nexus 93360YC-FX2 NX-OS Mode Switch Hardware Installation Guide

Summary of Contents for N9K-C93360YC-FX2









































































Search results

Summary of Contents for N9K-C93360YC-FX2

Reviews:

Related manuals for N9K-C93360YC-FX2

Brands by name

Popular brands

Cisco N9K-C93360YC-FX2, Hardware Installation Manual

Search results

Summary of Contents for N9K-C93360YC-FX2

Reviews:

Related manuals for N9K-C93360YC-FX2

Brands by name

Popular brands