background image

See

meraki.cisco.com/compliance

This device is a 2.4 GHz and 5 GHz wideband transmission system (transceiver), intended for use in all EU member
states and EFTA countries with the following restrictions:

Frequency Band
(MHz)

Max Power Level
(EIRP) (mW)

Indoor ONLY

Indoor and Outdoor

2400 - 2483.5

100

X

5150 - 5350

200

X

5470 - 5725

1000

X

Denmark

The band 5150-5350 MHz is also allowed for outdoor usage.

I Danmark må frekvensbåndet 5150-5350 også anvendes udendørs.

Italy

This product meets the National Radio Interface and the requirements specified in the National Frequency allocation
Table for Italy. Unless this wireless LAN product is operating within the boundaries of the owner’s property, its use
requires a “general authorization”.

Questo prodotto è conforme alla specifiche di Interfaccia Radio Nazionali e rispetta il Piano Nazionale di ripartizione
delle frequenze in Italia. Se non viene installato all ‘interno del proprio fondo, l’utilizzo di prodotti Wireless LAN richiede
una “Autorizzazione Generale”.

Latvia

The outdoor usage of the 2.4 GHz band requires an authorization from the Electronic Communications Office.

2.4 GHz frekvenču joslas izmantošanai ārpus telpām nepieciešama at auja no Elektronisko sakaru direkcijas.

Български (Bulgarian):

Настоящото Cisco Systems, Inc. декларира, че това безжичното устройство е в съответствие със съществените
изисквания и другите приложими разпоредби на Директива 1999/5/EC.

11

Summary of Contents for MERAKI MR72




















Reviews: