manualshive.com logo in svg

Cisco IE 4000, Software Configuration Manual

The Cisco IE 4000 is a powerful industrial Ethernet switch designed for seamless network connectivity in rugged environments. Experience optimal performance and reliability with its advanced features. Easily access the comprehensive user manual for this product, available for free download exclusively on our manualshive.com.

Share
Download
background image

961

   

Configuring Cisco IOS IP SLAs Operations

Information About Configuring Cisco IOS IP SLAs Operations

Figure 106 Cisco IOS IP SLAs Operation

To implement IP SLAs network performance measurement, you need to perform these tasks: 

—

Enable the IP SLAs responder, if required. 

—

Configure the required IP SLAs operation type. 

—

Configure any options available for the specified operation type. 

—

Configure threshold conditions, if required. 

—

Schedule the operation to run, then let the operation run for a period of time to gather statistics.

—

Display and interpret the results of the operation using the Cisco IOS CLI or a network management system 
(NMS) system with SNMP. 

IP SLAs Responder and IP SLAs Control Protocol 

The IP SLAs responder is a component embedded in the destination Cisco device that allows the system to anticipate 
and respond to IP SLAs request packets. The responder provides accurate measurements without the need for dedicated 
probes. The responder uses the Cisco IOS IP SLAs Control Protocol to provide a mechanism through which it can be 
notified on which port it should listen and respond. Only a Cisco IOS device can be a source for a destination IP SLAs 
Responder. 

Figure 106 on page 961

 shows where the Cisco IOS IP SLAs responder fits in the IP network. The responder listens on 

a specific port for control protocol messages sent by an IP SLAs operation. Upon receipt of the control message, it 
enables the specified UDP or TCP port for the specified duration. During this time, the responder accepts the requests 
and responds to them. It disables the port after it responds to the IP SLAs packet, or when the specified time expires. 
MD5 authentication for control messages is available for added security. 

You do not need to enable the responder on the destination device for all IP SLAs operations. For example, a responder 
is not required for services that are already provided by the destination router (such as Telnet or HTTP). You cannot 
configure the IP SLAs responder on non-Cisco devices and Cisco IOS IP SLAs can send operational packets only to 
services native to those devices. 

121381

IP SLA source

IP SLA responder

IP SLA 

Any IP device

SNMP

Performance

management

application

IP network

IP SLA 

IP SLA measurement

IP SLA measurement

and IP SLA responder to

and IP SLA responder to

IP SLA Responder

IP SLA Responder

IP SLA measurement

and IP SLA responder to

IP SLA responder

IP SLA measurement

and IP SLA responder to

IP SLA responder

Summary of Contents for IE 4000











































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for IE 4000

D-Link DSL-2640BT Installation Manual preview
DSL-2640BT
Brand: D-Link Pages: 12
i-MO 540 Series Product Installation Manual preview
540 Series
Brand: i-MO Pages: 58
Patton electronics Patton SmartNode 2300 Series Specification Sheet preview
Patton SmartNode 2300 Series
Brand: Patton electronics Pages: 2
Paradyne 8540 Installation Instructions Manual preview
8540
Brand: Paradyne Pages: 12
Aruba IntroSpect Analyzer 2 Series Quick Start Manual preview
IntroSpect Analyzer 2 Series
Brand: Aruba Pages: 5
ICP DAS USA USB-87P1 User Manual preview
USB-87P1
Brand: ICP DAS USA Pages: 62
Z-Com ZCN-1523H-5-16 Quick Installation Manual preview
ZCN-1523H-5-16
Brand: Z-Com Pages: 18
TP-Link TL-MR3620 Installation Manual preview
TL-MR3620
Brand: TP-Link Pages: 2
ADTRAN EXPRESS 6503 User Manual preview
EXPRESS 6503
Brand: ADTRAN Pages: 20
AIC SB302-LB User Manual preview
SB302-LB
Brand: AIC Pages: 101
Starbridge Networks ADSL Ethernet & USB Combo Router Lynx L-510 User Manual preview
ADSL Ethernet & USB Combo Router Lynx L-510
Brand: Starbridge Networks Pages: 59
CAME 848EA-0120 Setup And User'S Manual preview
848EA-0120
Brand: CAME Pages: 32
Variscite VAR-SOM-MX8M-PLUS Quick Start Manual preview
VAR-SOM-MX8M-PLUS
Brand: Variscite Pages: 2
Manson Engineering Industrial SBC-6108 User Manual preview
SBC-6108
Brand: Manson Engineering Industrial Pages: 10
Planet FNSW-1600P User Manual preview
FNSW-1600P
Brand: Planet Pages: 16
Vivotek ND8212W Hardware Installation Manual preview
ND8212W
Brand: Vivotek Pages: 46
Aaeon FWS-7811 Manual preview
FWS-7811
Brand: Aaeon Pages: 100
Network Instruments WAN Probe Kit Installation & Quick Start Manual preview
WAN Probe Kit
Brand: Network Instruments Pages: 44

Brands by name

Popular brands

Load more brands