manualshive.com logo in svg

Cisco IE 4000, Software Configuration Manual

The Cisco IE 4000 is a powerful industrial Ethernet switch designed for seamless network connectivity in rugged environments. Experience optimal performance and reliability with its advanced features. Easily access the comprehensive user manual for this product, available for free download exclusively on our manualshive.com.

Share
Download
background image

91

Cisco Systems, Inc.

www.cisco.com

 

Configuring Switch Clusters 

This chapter provides the concepts and procedures to create and manage switch clusters on your switch. You can create 
and manage switch clusters by using the command-line interface (CLI), Cisco Network Assistant (CNA) or SNMP. For 
information about CNA, see the online help for CNA.

This chapter provides information about switch clusters. It also includes guidelines and limitations for clusters mixed with 
other cluster-capable Catalyst switches, but it does not provide complete descriptions of the cluster features for 
switches in the cluster. For complete cluster information for a specific Catalyst platform, refer to the software 
configuration guide for that switch.

Cluster Command Switch Characteristics

A cluster command switch must meet these requirements:

Has an IP address.

Has Cisco Discovery Protocol (CDP) version 2 enabled (the default).

Is not a command or cluster member switch of another cluster.

Is connected to the standby cluster command switches through the management VLAN and to the cluster member 
switches through a common VLAN.

Standby Cluster Command Switch Characteristics

A standby cluster command switch must meet these requirements:

Has an IP address.

Has CDP version 2 enabled.

Is connected to the command switch and to other standby command switches through its management VLAN.

Is connected to all other cluster member switches (except the cluster command and standby command switches) 
through a common VLAN.

Is redundantly connected to the cluster so that connectivity to cluster member switches is maintained.

Is not a command or member switch of another cluster.

Candidate Switch and Cluster Member Switch Characteristics

Candidate switches

 are cluster-capable switches that have not yet been added to a cluster. Cluster member switches 

are switches that have actually been added to a switch cluster. Although not required, a candidate or cluster member 
switch can have its own IP address and password (for related considerations, see 

IP Addresses, page 99

 and 

Passwords, 

page 100

).

To join a cluster, a candidate switch must meet these requirements:

Is running cluster-capable software.

Summary of Contents for IE 4000











































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for IE 4000

H3C S3100 Series Operation Manual preview
S3100 Series
Brand: H3C Pages: 1057
3onedata IES615-2D Series Quick Installation Manual preview
IES615-2D Series
Brand: 3onedata Pages: 3
3One data 7212 User Manual preview
7212
Brand: 3One data Pages: 5
3onedata IEM615 Series Hardware User Manual preview
IEM615 Series
Brand: 3onedata Pages: 33
JB Systems Scene Master Operation Manual preview
Scene Master
Brand: JB Systems Pages: 24
JB Systems CMX 24 User Manual preview
CMX 24
Brand: JB Systems Pages: 61
Radwin Transportation FiberinMotion Deployment Manual preview
Transportation FiberinMotion
Brand: Radwin Pages: 122
FS FS-BOX-V3 Quick Start Manual preview
FS-BOX-V3
Brand: FS Pages: 19
Vaisala TERMBOX-1200 User Manual preview
TERMBOX-1200
Brand: Vaisala Pages: 32
Macsense MIH-108 User Manual preview
MIH-108
Brand: Macsense Pages: 39
Far Tools MR 40PB Original Manual Translation preview
MR 40PB
Brand: Far Tools Pages: 24
Maipu MP2900-04-AC Installation Manual preview
MP2900-04-AC
Brand: Maipu Pages: 80
Eaton SONiX Pm10 Technical Manual preview
SONiX Pm10
Brand: Eaton Pages: 14
Caton NVE 9100 User Manual preview
NVE 9100
Brand: Caton Pages: 18
Morrell SW-UNM-24FE2GC-24POE User Manual preview
SW-UNM-24FE2GC-24POE
Brand: Morrell Pages: 8
Hamlet HRDSL742 User Manual preview
HRDSL742
Brand: Hamlet Pages: 122
LaCie 301297U - 1TB Ethernet Disk XP Embedded Network Attached... Online Manual preview
301297U - 1TB Ethernet Disk XP Embedded Network Attached...
Brand: LaCie Pages: 67
Digisol DG-BG4100NU Quick Installation Manual preview
DG-BG4100NU
Brand: Digisol Pages: 22

Brands by name

Popular brands

Load more brands