manualshive.com logo in svg

Cisco IE 4000, Software Configuration Manual

The Cisco IE 4000 is a powerful industrial Ethernet switch designed for seamless network connectivity in rugged environments. Experience optimal performance and reliability with its advanced features. Easily access the comprehensive user manual for this product, available for free download exclusively on our manualshive.com.

Share
Download
background image

894

Configuring IP Unicast Routing

 

Configuring Multi-VRF CE

DETAILED STEPS

To reenable echo mode on the switch, enter the 

bfd echo 

global configuration command. 

EXAMPLE

The following example disables echo mode between BFD neighbors:

Switch# 

configure terminal

Switch(config)# 

interface Ethernet 0/1

Switch(config-if)# 

no bfd echo

Configuring Multi-VRF CE

Virtual Private Networks (VPNs) provide a secure way for customers to share bandwidth over an ISP backbone network. 
A VPN is a collection of sites sharing a common routing table. A customer site is connected to the service-provider 
network by one or more interfaces, and the service provider associates each interface with a VPN routing table, called a 
VPN routing/forwarding (VRF) table. 

The switch supports multiple VPN routing/forwarding (multi-VRF) instances in customer edge (CE) devices (multi-VRF 
CE). With multi-VRF CE, a service provider can support two or more VPNs with overlapping IP addresses. 

Note: 

The switch does not use Multiprotocol Label Switching (MPLS) to support VPNs. For information about MPLS VRF, 

refer to the

 

MPLS: Layer 3 VPNs Configuration Guide, Cisco IOS Release 15M&T

.

Information About Multi-VRF CE, page 895

Default Multi-VRF CE Configuration, page 896

Multi-VRF CE Configuration Guidelines, page 896

Configuring VRFs, page 897

Configuring VRF-Aware Services, page 898

Configuring a VPN Routing Session, page 903

Configuring BGP PE to CE Routing Sessions, page 904

Displaying Multi-VRF CE Status, page 905

Command

Purpose

1.

configure terminal

Enter global configuration mode.

2.

interface

 

interface-id

Enter a BFD interface and enter interface configuration mode.

3.

no bfd echo 

Disable BFD echo mode on the interface. It is enabled by default, 
but can be disabled independently on BFD neighbors.

4.

exit

Return to global configuration mode.

5.

bfd slow-timer

 [

milliseconds

] 

(Optional) Configure a BFD slow-timer value. The range is from 
1000 to 30000 milliseconds. The default is 1000 milliseconds.

6.

end

 

Return to privileged EXEC mode.

7.

show bfd neighbors detail

Verify your entries. 

8.

copy running-config 
startup-config

 

(Optional) Save your entries in the configuration file.

Summary of Contents for IE 4000











































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for IE 4000

Linksys WRT54G3G-AT Product Data preview
WRT54G3G-AT
Brand: Linksys Pages: 2
PaloAlto Networks PA-7500 Quick Start Manual preview
PA-7500
Brand: PaloAlto Networks Pages: 3
LaCie 5BIG NAS PRO Quick Install Manual preview
5BIG NAS PRO
Brand: LaCie Pages: 22
Banner Sure Cross DX70 Instruction Manual preview
Sure Cross DX70
Brand: Banner Pages: 35
Compaq StorageWorks AIT 35GB AutoLoader Overview And Installation preview
StorageWorks AIT 35GB AutoLoader
Brand: Compaq Pages: 4
TP-Link TL-SG2424P User Manual preview
TL-SG2424P
Brand: TP-Link Pages: 176
Ubiquiti EdgeRouter PoE ERPoe-5 Quick Start Manual preview
EdgeRouter PoE ERPoe-5
Brand: Ubiquiti Pages: 13
Nilox 16NX071900001 User Manual preview
16NX071900001
Brand: Nilox Pages: 66
Accton Technology MR3202A User Manual preview
MR3202A
Brand: Accton Technology Pages: 78
Westermo Ibex-RT-330-HV User Manual preview
Ibex-RT-330-HV
Brand: Westermo Pages: 34
Global Sun GL-241101 User Manual preview
GL-241101
Brand: Global Sun Pages: 39
i-MO OptiBond 210 C Series Hardware Installation Manual preview
OptiBond 210 C Series
Brand: i-MO Pages: 16
B+B SmartWorx Airborne M2M ABDN-er-DP55 Series User Manual preview
Airborne M2M ABDN-er-DP55 Series
Brand: B+B SmartWorx Pages: 120
Echelon i.LON SmartServer Hardware Manual preview
i.LON SmartServer
Brand: Echelon Pages: 34
Perle IRG5540 Quick Start Manual preview
IRG5540
Brand: Perle Pages: 4
Inter-m S- Media Manual preview
S- Media
Brand: Inter-m Pages: 20
Linksys USB100H1 User Manual preview
USB100H1
Brand: Linksys Pages: 44
H3C LS-5100-16P-SI-OVS-H3 Configuration preview
LS-5100-16P-SI-OVS-H3
Brand: H3C Pages: 313

Brands by name

Popular brands

Load more brands