manualshive.com logo in svg

Cisco IE 4000, Software Configuration Manual

The Cisco IE 4000 is a powerful industrial Ethernet switch designed for seamless network connectivity in rugged environments. Experience optimal performance and reliability with its advanced features. Easily access the comprehensive user manual for this product, available for free download exclusively on our manualshive.com.

Share
Download
background image

897

   

Configuring IP Unicast Routing

Configuring Multi-VRF CE

Multi-VRF CE does not support all MPLS-VRF functionality. It does not support label exchange, LDP adjacency, or 
labeled packets.

For the PE router, there is no difference between using multi-VRF CE or using multiple CEs. In 

Figure 104 on 

page 895

, multiple virtual Layer 3 interfaces are connected to the multi-VRF CE device.

The switch supports configuring VRF by using physical ports, VLAN SVIs, or a combination of both. The SVIs can be 
connected through an access port or a trunk port.

A customer can use multiple VLANs as long as they do not overlap with those of other customers. A customer’s 
VLANs are mapped to a specific routing table ID that is used to identify the appropriate routing tables stored on the 
switch.

The switch supports one global network and up to 26 VRFs.

Most routing protocols (BGP, OSPF, RIP, EIGRP, and static routing) can be used between the CE and the PE. However, 
we recommend using external BGP (EBGP) for these reasons:

—

BGP does not require multiple algorithms to communicate with multiple CEs. 

—

BGP is designed for passing routing information between systems run by different administrations.

—

BGP makes it easy to pass attributes of the routes to the CE.

Multi-VRF CE does not affect the packet switching rate.

If no VRFs are configured, up to 105 policies can be configured.

If even one VRF is configured than 41 policies can be configured.

If more than 41 policies are configured then VRF cannot be configured.

VRF and private VLANs are mutually exclusive. You cannot enable VRF on a private VLAN. Similarly, you cannot 
enable private VLAN on a VLAN with VRF configured on the VLAN interface.

VRF and policy-based routing (PBR) are mutually exclusive on a switch interface. You cannot enable VRF when PBR 
is enabled on an interface. In contrast, you cannot enable PBR when VRF is enabled on an interface.

Configuring VRFs

Follow the steps in this procedure to configure one or more VRFs. 

BEFORE YOU BEGIN

See 

Multi-VRF CE Configuration Guidelines, page 896

.

Summary of Contents for IE 4000











































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for IE 4000

Vivotek NR8401 User Manual preview
NR8401
Brand: Vivotek Pages: 136
ZyXEL Communications ZyXEL EES-1024AF User Manual preview
ZyXEL EES-1024AF
Brand: ZyXEL Communications Pages: 99
National Instruments NI WLS/ENET-9163 User Manual preview
NI WLS/ENET-9163
Brand: National Instruments Pages: 36
Extron electronics PoleVault System A/V Source Inputs Specification Sheet preview
PoleVault System A/V Source Inputs
Brand: Extron electronics Pages: 4
WABCO CAN Router Manual preview
CAN Router
Brand: WABCO Pages: 29
Patton DiamondLink 3201 Quick Start Manual preview
DiamondLink 3201
Brand: Patton Pages: 12
Fastech Ezi-SERVOII EtherCAT TO User Manual preview
Ezi-SERVOII EtherCAT TO
Brand: Fastech Pages: 108
Global411 MS41p1 Quick Installation Manual preview
MS41p1
Brand: Global411 Pages: 15
NETGEAR RP614 - Web Safe Router Installation Manual preview
RP614 - Web Safe Router
Brand: NETGEAR Pages: 16
ivideon Bridge B1610 Quick Start Manual preview
Bridge B1610
Brand: ivideon Pages: 11
Microtek MiniLink Operation Manual preview
MiniLink
Brand: Microtek Pages: 25
LaView LV-KN series Quick Start Manual preview
LV-KN series
Brand: LaView Pages: 2
NetComm Dynalink MyZone 3G24W Remote Administration Setup preview
Dynalink MyZone 3G24W
Brand: NetComm Pages: 5
ADTRAN 1700600L2 Quick Start preview
1700600L2
Brand: ADTRAN Pages: 4
Telestar DIGIBIT R1 Operating Manual preview
DIGIBIT R1
Brand: Telestar Pages: 16
Paradyne 8310 MVLt User Manual preview
8310 MVLt
Brand: Paradyne Pages: 108
Vaisala TERMBOX-9000 User Manual preview
TERMBOX-9000
Brand: Vaisala Pages: 32
ADTRAN 1202880E1 Quick Start Manual preview
1202880E1
Brand: ADTRAN Pages: 4

Brands by name

Popular brands

Load more brands