manualshive.com logo in svg

Cisco IE 4000, Software Configuration Manual

The Cisco IE 4000 is a powerful industrial Ethernet switch designed for seamless network connectivity in rugged environments. Experience optimal performance and reliability with its advanced features. Easily access the comprehensive user manual for this product, available for free download exclusively on our manualshive.com.

Share
Download
background image

826

Configuring IP Unicast Routing

 

Configuring OSPF

Nonstop Forwarding Awareness

The OSPF NSF Awareness feature is supported for IPv4 in the IP services image. When the neighboring router is 
NSF-capable, the Layer 3 switch continues to forward packets from the neighboring router during the interval between 
the primary Route Processor (RP) in a router crashing and the backup RP taking over, or while the primary RP is manually 
reloaded for a non-disruptive software upgrade. 

This feature cannot be disabled. For more information about this feature, see the 

“Configuring Nonstop Forwarding”

 

chapter in the 

High Availability Configuration Guide, Cisco IOS Release 15S

.

Configuring Basic OSPF Parameters

Enabling OSPF requires that you create an OSPF routing process, specify the range of IP addresses to be associated 
with the routing process, and assign area IDs to be associated with that range. 

BEFORE YOU BEGIN

Complete the OSPF network strategy and planning for your network. For example, you must decide whether multiple 
areas are required.

Timers LSA group pacing

240 seconds.

Timers shortest path first (spf)

spf delay: 5 seconds.

spf-holdtime: 10 seconds.

Virtual link

No area ID or router ID defined.

Hello interval: 10 seconds.

Retransmit interval: 5 seconds.

Transmit delay: 1 second.

Dead interval: 40 seconds.

Authentication key: no key predefined.

Message-digest key (MD5): no key predefined.

1.

NSF = Nonstop forwarding

2.

OSPF NSF awareness is enabled for IPv4 on switches running the IP services image.

Feature

Default Setting

Summary of Contents for IE 4000











































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for IE 4000

WAGO 852-1417 Operating And Assembly Instructions preview
852-1417
Brand: WAGO Pages: 2
iDirect iQ Desktop+ Installation, Support, And Maintenance Manual preview
iQ Desktop+
Brand: iDirect Pages: 52
Dust Networks SmartMesh IA-510 D2511 Manager'S Manual preview
SmartMesh IA-510 D2511
Brand: Dust Networks Pages: 30
Draytek Vigor 2700G Specifications preview
Vigor 2700G
Brand: Draytek Pages: 2
Genie IP8ESP User Manual preview
IP8ESP
Brand: Genie Pages: 6
i-MO OptiBond 210 C Series Hardware Installation Manual preview
OptiBond 210 C Series
Brand: i-MO Pages: 16
Tripp Lite N310-30M Specification Sheet preview
N310-30M
Brand: Tripp Lite Pages: 2
Alcatel-Lucent 9364 Installation And Commissioning Manual preview
9364
Brand: Alcatel-Lucent Pages: 60
UNICOM DynaGST/2402G GEP-33224T-1 User Manual preview
DynaGST/2402G GEP-33224T-1
Brand: UNICOM Pages: 17
Vivint AirBridge VS-YOFIMN-000 Quick Reference preview
AirBridge VS-YOFIMN-000
Brand: Vivint Pages: 2
Pro-Nets Technology Corporation WR750RL User Manual preview
WR750RL
Brand: Pro-Nets Technology Corporation Pages: 48
Delta Electronics CANopen Communication Module DVPCP02-H2 Instruction Manual preview
CANopen Communication Module DVPCP02-H2
Brand: Delta Electronics Pages: 2
Hameg HM6050-2K Manual preview
HM6050-2K
Brand: Hameg Pages: 46
Helmholz REX 100 3G Quick Start Manual preview
REX 100 3G
Brand: Helmholz Pages: 20
Geneko GWR-A362 Quick Start Manual preview
GWR-A362
Brand: Geneko Pages: 8
Linksys EFG20 User Manual preview
EFG20
Brand: Linksys Pages: 37
Planet MGSD SERIES Quick Installation Manual preview
MGSD SERIES
Brand: Planet Pages: 16
Alcatel-Lucent 5620 Planning Manual preview
5620
Brand: Alcatel-Lucent Pages: 144

Brands by name

Popular brands

Load more brands