manualshive.com logo in svg

Cisco IE 4000, Software Configuration Manual

The Cisco IE 4000 is a powerful industrial Ethernet switch designed for seamless network connectivity in rugged environments. Experience optimal performance and reliability with its advanced features. Easily access the comprehensive user manual for this product, available for free download exclusively on our manualshive.com.

Share
Download
background image

353

Cisco Systems, Inc.

www.cisco.com

 

Configuring Optional Spanning-Tree 
Features 

Prerequisites for the Optional Spanning-Tree Features

 

You can configure all of these features when your switch is running the per-VLAN spanning-tree plus (PVST+). You can 
configure only the noted features when your switch is running the Multiple Spanning Tree Protocol (MSTP) or the rapid 
per-VLAN spanning-tree plus (rapid-PVST+) protocol. 

Restrictions for the Optional Spanning-Tree Features 

You can configure the UplinkFast or the BackboneFast feature for rapid PVST+ or for the MSTP, but the feature remains 
disabled (inactive) until you change the spanning-tree mode to PVST+.

Information About Configuring the Optional Spanning-Tree 
Features 

PortFast

PortFast immediately brings an interface configured as an access or trunk port to the forwarding state from a blocking 
state, bypassing the listening and learning states. You can use PortFast on interfaces connected to a single workstation 
or server, as shown in 

Figure 44 on page 354

, to allow those devices to immediately connect to the network, rather than 

waiting for the spanning tree to converge. 

Interfaces connected to a single workstation or server should not receive bridge protocol data units (BPDUs). An interface 
with PortFast enabled goes through the normal cycle of spanning-tree status changes when the switch is restarted.

Note: 

Because the purpose of PortFast is to minimize the time interfaces must wait for spanning-tree to converge, it is 

effective only when used on interfaces connected to end stations. If you enable PortFast on an interface connecting to 
another switch, you risk creating a spanning-tree loop. 

You can enable this feature by using the 

spanning-tree portfast

 interface configuration or the 

spanning-tree portfast

 

default

 global configuration command.

Summary of Contents for IE 4000











































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for IE 4000

Radwin Transportation FiberinMotion Deployment Manual preview
Transportation FiberinMotion
Brand: Radwin Pages: 122
Ruckus Wireless SmartZone 3.6 Command Reference Manual preview
SmartZone 3.6
Brand: Ruckus Wireless Pages: 102
APM AQ-500h Specification Sheet preview
AQ-500h
Brand: APM Pages: 3
Patton electronics 3040/V35 Installation And Operation Manual preview
3040/V35
Brand: Patton electronics Pages: 23
HARTING HAIIC MICA Hardware Development Manual preview
HAIIC MICA
Brand: HARTING Pages: 13
XNET INS2000 Install Manual preview
INS2000
Brand: XNET Pages: 17
Ruckus Wireless MediaFlex NG Quick Installation Manual preview
MediaFlex NG
Brand: Ruckus Wireless Pages: 2
Rosewill RNX-N150RT Quick Installation Manual preview
RNX-N150RT
Brand: Rosewill Pages: 10
1&1 Homeserver+ Quick Start Manual preview
Homeserver+
Brand: 1&1 Pages: 32
Sparklan WNFB-265AXI(BT) User Manual preview
WNFB-265AXI(BT)
Brand: Sparklan Pages: 14
Aviosys 9255W User Manual preview
9255W
Brand: Aviosys Pages: 77
Echelon i.LON SmartServer Hardware Manual preview
i.LON SmartServer
Brand: Echelon Pages: 34
Hi-flying HF-LPB User Manual preview
HF-LPB
Brand: Hi-flying Pages: 59
Teldat H2 RAIL Installation Manual preview
H2 RAIL
Brand: Teldat Pages: 47
Radio Shack TRS-80 PTC-64 Operation Manual preview
TRS-80 PTC-64
Brand: Radio Shack Pages: 40
QCT QuantaGrid D51PH-1ULH Service Manual preview
QuantaGrid D51PH-1ULH
Brand: QCT Pages: 167
Allied Telesis AR100 series User Manual preview
AR100 series
Brand: Allied Telesis Pages: 128
TheGreenBow IPSec VPN Client Zyxel ZyWall 10 Configuration Manual preview
IPSec VPN Client Zyxel ZyWall 10
Brand: TheGreenBow Pages: 12

Brands by name

Popular brands

Load more brands