manualshive.com logo in svg

Cisco IE 2000U Series, Product Overview, Page: 13 / 20

Share
Download
Cisco IE 2000U Series Product Overview Download Page 13

21

 

      

The alarm connector provides six alarm wire connections. The connector is attached to the switch front panel with the 
provided captive screws.

Figure 8

Alarm Connector

Both alarm input circuits can sense if the alarm input is open or closed. The alarm inputs can be activated for 
environmental, power supply, and port status alarm conditions. From the CLI, you can configure each alarm input as an 
open or closed contact.

The alarm output circuit is a relay with a normally open and a normally closed contact. The switch is configured to detect 
faults that are used to energize the relay coil and change the state on both of the relay contacts: normally open contacts 
close, and normally closed contacts open. The alarm output relay can be used to control an external alarm device, such 
as a bell or a light.

See the 

Cisco Connected Grid Switches System Management Software Configuration Guide

 

for instructions on 

configuring the alarm relays.

For more information about the alarm connector, see 

Cable and Connectors, page 83

Management Ports

You can connect the switch to a PC running Microsoft Windows or to a terminal server through either the RJ-45 console 
port or the USB mini-Type B console port, also referred to as the USB-mini console port. These ports use the following 
connectors:

RJ-45 console port uses an RJ-45-to-DB-9 female cable.

USB-mini console port (5-pin connector) uses a USB Type A-to-5-pin mini-Type B cable. 

The USB-mini console interface speeds are the same as the RJ-45 console interface speeds.

To use the USB-mini console port, you must install the Cisco Windows USB device driver on the device that is connected 
to the USB-mini console port and that is running Microsoft Windows. 

Note: 

For information about downloading the Cisco USB device driver, see the 

Installing the Cisco Microsoft Windows 

USB Device Driver, page 97

.

With the Cisco Windows USB device driver, connecting and disconnecting the USB cable from the console port does not 
affect Windows HyperTerminal operations. Mac OS X or Linux requires no special drivers. 

Note: 

The 5-pin mini-Type B connectors resemble the 4-pin mini-Type B connectors, but they are not compatible. Use 

only the 5-pin mini-Type B. See 

Figure 9 on page 22

.

331208

Summary of Contents for IE 2000U Series





















Reviews:

No comments