Cisco Fourth-Generation Versatile Interface Processor VIP4 Installation And Configuration Manual Download Page 7 | Manualshive

Page: 7 / 44

background image

7

Fourth Generation Versatile Interface Processor (VIP4) Installation and Configuration Guide

OL-3673-01

VIP4 Overview

VIP4 and Port Adapter Compatibility

For more information on the available port adapters supported by the VIP4, refer to the Cisco Product
Catalog online, or contact a Cisco sales representative in your area. For more information on a specific
port adapter, refer to the specific port adapter installation and configuration guide. The port adapters,
including part numbers for ordering, are listed in the Cisco Port Adapter Documentation flyer. This
document is available online at

http://www.cisco.com/univercd/cc/td/doc/product/core/12939paf.htm

or

in print (DOC-7812939).

Note

The VIP4 does not support the PA-GE. However, the VIP4-80 supports the Enhanced Gigabit Ethernet
Interface Processor (GEIP+), an assembly consisting of a VIP4-80 with a permanently attached
dual-width Enhanced Gigabit Ethernet port adapter.

Table 5

identifies the port adapters supported by the VIP4 at the time of this writing, and

Table 6

identifies the interface processors and service adapters that are supported by the VIP4.

Note

The following table does not address which software release applies to the VIP6-80 port adapters. For
more information, refer to the Software Advisor at

http://www.cisco.com/cgi-bin/Support/CompNav/Index.pl

.

Table 5

List of Port Adapters Supported by VIP4

Product Number

Description

Number of
Ports

Single/Dual Width

PA-A3-T3

ATM DS3 port adapter, enhanced

1

Single

PA-A3-E3

ATM E3 port adapter, enhanced

1

Single

PA-A3-8T1IMA

ATM inverse multiplexer over ATM port adapter

8

Single

PA-A3-8E1IMA

ATM inverse multiplexer over ATM port adapter

8

Single

PA-A3-OC3MM

ATM OC-3c/STM-1 multimode, enhanced

1

Single

PA-A3-OC3SMI

ATM OC-3c/STM-1 single-mode (IR), enhanced

1

Single

PA-A3-OC3SML

ATM OC-3c/STM-1 single-mode (LR), enhanced

1

Single

PA-A3-OC12-MM

ATM OC-12/STM-4 single-mode (IR); multimode

1

Dual

PA-A3-OC12-SMI

ATM OC-12/STM-4 single-mode (IR); multimode

1

Dual

PA-POS-OC3- MM

Single-wide OC-3c/STM-1

1

Single

PA-POS-OC3- SMI

Single-wide OC-3c/STM-1

1

Single

PA-POS-OC3- SML

Single-wide OC-3c/STM-1

1

Single

PA-A1-OC3SM

ATM OC3 Single-Mode Intermediate Reach

1

Single

PA-A1-OC3MM

ATM OC3 Multimode

1

Single

PA-FE-TX

Fast Ethernet 100BaseTX

1

Single

PA-FE-FX

Fast Ethernet 100BaseFX

1

Single

PA-2FE-TX

Dual-Port Fast Ethernet 100BaseTX

2

Single

PA-2FE-FX

Dual-Port Fast Ethernet 100BaseFX

2

Single

PA-4E

Ethernet 10BaseT

4

Single

«
...
5
6
7
8
9
...
»

Summary of Contents for Fourth-Generation Versatile Interface Processor VIP4













































Reviews:

No comments

Related manuals for Fourth-Generation Versatile Interface Processor VIP4

Brand: Dahua Pages: 24

Brand: Paradyne Pages: 112

Brand: Cambium Networks Pages: 215

HAWA-Frontside 60/B

Brand: hawa Pages: 28

Brand: ADTRAN Pages: 9

Brand: ForeScout Pages: 28

Brand: Direct IP Pages: 76

Brand: Quectel Pages: 23

Brand: Bridgeworks Pages: 18

Brand: Qixiang Technology Pages: 16

Hollywood DV-Bridge

Brand: Dazzle Pages: 63

LinkStation Mini

Brand: Buffalo Pages: 71

Brand: M86 Security Pages: 309

Brand: Selta Pages: 83

18x18 Card Cage

Brand: WolfPack Pages: 31

Brand: Infoblox Pages: 13

ELITENAS EN104L+(B)

Brand: Sans Digital Pages: 9

Brand: Compro Technology Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands