manualshive.com logo in svg

Cisco CPANM-1CE1-B, Configuration Note

Share
Download
Cisco CPANM-1CE1-B Configuration Note Download Page 22

22 1-Port and 2-Port ISDN-PRI Network Module Configuration Note

Obtaining Service and Support

Note

For further information about the memory-size iomem command, refer to the

Cisco IOS configuration guides and command references.

Step 14

When you are finished configuring interfaces, exit configuration mode and return to the
enable prompt by pressing Ctrl-Z. To see the current operating configuration, including
any changes you just made, enter the show running-config command:

Router# show running-config

To see the configuration currently stored in nonvolatile random-access memory
(NVRAM), enter the command show startup-config at the enable prompt.

Router# show startup-config

Step 15

The results of the show running-config and show startup-config commands differ from
each other if you have made changes to the configuration, but have not yet written them
to NVRAM. To write your changes to NVRAM, making them permanent, enter the
command copy running-config startup-config at the enable prompt:

Router# copy running-config startup-config

Building configuration. . .

[OK]

Router#

The router is now configured to boot in the new configuration.

Obtaining Service and Support

For service and support for a product purchased from a reseller, contact the reseller. Resellers offer
a wide variety of Cisco service and support programs, which are described in the section “Service
and Support” in the information packet that shipped with your chassis.

Note

If you purchased your product from a reseller, you can access Cisco Connection Online

(CCO) as a guest. CCO is Cisco Systems’ primary, real-time support channel. Your reseller offers
programs that include direct access to CCO’s services.

For service and support for a product purchased directly from Cisco, use CCO.

Cisco Connection Online

CCO is Cisco Systems’ primary, real-time support channel. SMARTnet customers and partners can
self-register on CCO to obtain additional content and services.

Note

If you purchased your product from a reseller, you can access CCO as a guest. Your reseller

offers programs that include direct access to CCO’s services.

Summary of Contents for CPANM-1CE1-B

























Reviews:

No comments

Brands by name

Popular brands

Load more brands