Cisco Catalyst 9200CX Compact Series Hardware Installation Manual Download Page 19 | Manualshive

Page: 19 / 70

background image

This warning symbol means danger. You are in a situation that could cause bodily injury. Before you
work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar with
standard practices for preventing accidents. Use the statement number provided at the end of each
warning to locate its translation in the translated safety warnings that accompanied this device. Statement
1071

Warning

No user-serviceable parts inside. Do not open. Statement 1073

Warning

Installation of the equipment must comply with local and national electrical codes. Statement 1074

Warning

To prevent airflow restriction, allow clearance around the ventilation openings to be at least: 3 inches
(7.6 cm). Statement 1076

Warning

Hot surface. Statement 1079

Warning

Installation Guidelines

When determining where to install the switch, verify that these guidelines are met:

• Clearance to the switch front and rear panel meets these conditions:

• Front-panel LEDs can be easily read.

• AC power cord reaches from the power outlet to the connector on the switch.

• Cabling is away from sources of electrical noise, such as radios, power lines, and fluorescent lighting

fixtures. Make sure that the cabling is safely away from other devices that might damage the cables.

• Installation temperature should be measured within 1 inches from the sides of the switch. Airflow around

the switch and through the vents is unrestricted. To avoid any airflow blockage, we recommend the
following:

• Allow at least 3 inches (7.6 cm) of clearance around the switch.

• When placing the switch on a flat horizontal surface, attach the rubber feet to the switch.

• Maximum installation temperature may be limited by the SFPs used. Refer to the datasheet for specific

restrictions.

• For 10/100/1000 fixed ports, cable lengths from the switch to connected devices can be up to 328 feet

(100 meters).

Cisco Catalyst 9200CX Compact Series Switches Hardware Installation Guide

11

Preparing for Installation

Installation Guidelines

«
...
17
18
19
20
21
...
»

Summary of Contents for Catalyst 9200CX Compact Series







































































Reviews:

No comments

Related manuals for Catalyst 9200CX Compact Series

Brand: AAVARA Pages: 23

Brand: Campbell Hausfeld Pages: 12

Brand: Dataprobe Pages: 21

Brand: AVE Pages: 2

Brand: Little Giant Pages: 2

Brand: Erbe Pages: 118

Brand: Accton Technology Pages: 10

Brand: Lancom Pages: 23

Brand: Advantech Pages: 101

Brand: enbrighten Pages: 2

Brand: Link Pages: 35

Brand: Extron electronics Pages: 6

Master View CS-102

Brand: ATEN Pages: 11

Champion KD-4X4XC

Brand: Key Digital Pages: 8

Brand: AAVARA Pages: 8

Atlona AT-HDR-SW-52ED

Brand: Panduit Pages: 81

Brand: Whelen Engineering Company Pages: 5

Brand: CAME Pages: 5

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands