manualshive.com logo in svg

Cisco Catalyst 4500 Series, Software Configuration Manual

The Cisco Catalyst 4500 Series is a powerful network switch offering seamless connectivity and efficient performance. To unlock the full potential of this product, users can easily download the comprehensive Command Reference Manual for free from our website, ensuring hassle-free operation and optimal network management.

Share
Download
background image

42-6

Catalyst 4500 Series Switch, Cisco IOS Software Configuration Guide - Cisco IOS XE 3.9.xE and IOS 15.2(5)Ex

 

Chapter 42      Configuring Policy-Based Routing

Policy-Based Routing

route-maps (each containing ACLs with permit ACEs only) may require 6-7 minutes of flatten time 
before programming into hardware. This process may repeat if an adjacency change requires PBR 
reprogramming.

Policy-Based Routing with Object Tracking

Beginning in Cisco IOS XE Release 3.8.0E and Cisco IOS Release 15.2(4)E, you can configure 
Policy-Based Routing (PBR) to use object tracking, to verify the most viable next-hop IP address to 
which to forward packets, using an Internet Control Message Protocol (ICMP) ping as the verification 
method. PBR used with object tracking is most suitable for devices that have multiple Ethernet 
connections as the next hop. Normally, Ethernet interfaces connect to digital subscriber line (DSL) 
modems or cable modems, and do not detect a failure upstream in the ISP broadband network. The 
Ethernet interface remains up, and any form of static routing points to that interface. Using PBR with 
object tracking allows you to back-up two Ethernet interfaces, determine the interface that is available 
by sending ICMP pings to verify if the IP address can be reached, and then route traffic to that interface. 

To verify the next-hop IP address for the device, PBR informs the object tracking process that it is 
interested in tracking a certain object. The tracking process, in turn, informs PBR when the state of the 
object changes. 

Restrictions for Policy-Based Routing with Object Tracking 

The 

set next-hop verify-availability

 command is not supported with the following: 

•

VRF instances

•

Virtual switching system (VSS) 

•

IPv6 traffic 

IPv4 and IPv6 Policy-Based Routing for VRF Instances

Virtual routing and forwarding (VRF) allows multiple routing instances in Cisco software. Beginning in 
Cisco IOS Release XE 3.7 0E and IOS 15.2(3)E, the Policy-Based Routing (PBR) feature is VRF-aware 
and works on multiple routing instances, beyond the default or global routing table.

Incoming packets are filtered through the match criteria that are defined in the route map. After a 
successful match occurs, the 

set 

command configuration determines the VRF through which outbound 

packets are policy routed.

Inherit-VRF, Inter-VRF, Global-to-VRF, and VRF-to-Global Routing

The Policy-Based Routing feature supports inherit-VRF, inter-VRF, and VRF-to-global routing. 

With inherit-VRF, packets arriving at a virtual routing and forwarding (VRF) interface are routed, by 
looking-up the same VRF’s routing table.

With inter-VRF routing, packets arriving at a VRF interface are routed, by looking-up a different VRF’s 
routing table, as specified by the 

set

 command.

With VRF-to-global routing, packets arriving at a VRF interface are routed via the global routing table.

With global-to-VRF routing, packets arriving at the global interface (an interface that is not part of a 
VRF) are routed via a VRF routing table.

Summary of Contents for Catalyst 4500 Series







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Catalyst 4500 Series

Ubiquiti M900 Quick Start Manual preview
M900
Brand: Ubiquiti Pages: 24
Patton electronics 2888 Getting Started Manual preview
2888
Brand: Patton electronics Pages: 51
Idis DR-6100 Series Operation Manual preview
DR-6100 Series
Brand: Idis Pages: 86
Paradyne Hotwire 6301 Installation Instructions Manual preview
Hotwire 6301
Brand: Paradyne Pages: 20
Paradyne COMSPHERE 3610 Installation Instructions preview
COMSPHERE 3610
Brand: Paradyne Pages: 2
Lanner NCA-4035 User Manual preview
NCA-4035
Brand: Lanner Pages: 109
PairGain PG-FLEX RT FRL-752 Manual preview
PG-FLEX RT FRL-752
Brand: PairGain Pages: 6
Aztech DSL1000EW(L) Speci?Cations preview
DSL1000EW(L)
Brand: Aztech Pages: 2
Delta Electronics DTE-20T Instruction Sheet preview
DTE-20T
Brand: Delta Electronics Pages: 1
TRENDnet TW-100 Specifications preview
TW-100
Brand: TRENDnet Pages: 2
Weidmuller IE-SW-VL16-14TX-2SC Hardware Installation Manual preview
IE-SW-VL16-14TX-2SC
Brand: Weidmuller Pages: 17
HELVAR Imagine 920 Installation Manual preview
Imagine 920
Brand: HELVAR Pages: 2
TDK InvenSense RoboKit1 Hardware Reference Manual preview
InvenSense RoboKit1
Brand: TDK Pages: 13
ANEP P4GU VoLTE Technical Data Sheet preview
P4GU VoLTE
Brand: ANEP Pages: 48
Planet GSW-2416SF User Manual preview
GSW-2416SF
Brand: Planet Pages: 54
Parker Sporlan Division SCS-PB Series Installation And Operating Instructions Manual preview
Sporlan Division SCS-PB Series
Brand: Parker Pages: 10
Cabletron Systems TRXMIM-24A User Manual preview
TRXMIM-24A
Brand: Cabletron Systems Pages: 56
TRENDnet TEG-PCITX User Manual preview
TEG-PCITX
Brand: TRENDnet Pages: 15

Brands by name

Popular brands

Load more brands