Cisco Catalyst 3550 Page 79 Installation Manual Download

Page: 79 / 154

2-29

Catalyst 3550 Multilayer Switch Hardware Installation Guide

78-11358-03

Chapter 2 Installing and Starting the Switch

Connecting to DC Power

Caution

You must connect the Catalyst 3550-24-DC switch only to a DC-input power
source that has an input supply voltage from –36 to –72 VDC. If the supply
voltage is not in this range, the switch might not operate properly or might be
damaged.

Caution

The switch must be installed with 5A-branch-circuit protection.

Note

This installation must comply with all applicable codes.

To wire the switch to a DC-input power source, follow these steps:

Step 1

Locate and remove the terminal block plug (see

Figure 2-27

Figure 2-27 Terminal Block Plug

60530

Summary of Contents for Catalyst 3550



























































































































































Search results

Summary of Contents for Catalyst 3550

Reviews:

Related manuals for Catalyst 3550

Brands by name

Popular brands

Cisco Catalyst 3550, Installation Manual

Search results

Summary of Contents for Catalyst 3550

Reviews:

Related manuals for Catalyst 3550

Brands by name

Popular brands