Cisco CAB-SM-LCSC-1M Installation Notes Download

Page: 36 / 42

Cisco Enhanced Wave Division Multiplexing Optical System Installation Note

78-17894-02

Translated Safety Warnings

Statement 1055—Class I and Class 1M Laser

Varning!

Klass 1M laser utstrålning när öppen. Betrakta ej direkt med optiska instrument.

Warning

Class I (CDRH) and Class 1M (IEC) laser products.

Waarschuwing

Laserproducten van Klasse I (CDRH) en Klasse 1M (IEC).

Varoitus

Luokan I (CDRH) ja luokan 1M (IEC) lasertuotteita.

Attention

Produits laser catégorie I (CDRH) et catégorie 1M (IEC).

Warnung

Laserprodukte der Klasse I (CDRH) und Klasse 1M (IEC).

Avvertenza

Prodotti laser di Classe I (CDRH) e Classe 1M (IEC).

Advarsel

Klasse I (CDRH) og klasse 1M (IEC) laserprodukter.

Aviso

Produtos laser Classe I (CDRH) e Classe 1M (IEC).

¡Advertencia!

Productos láser de Clase I (CDRH) y Clase 1M (IEC).

Summary of Contents for CAB-SM-LCSC-1M











































Search results

Summary of Contents for CAB-SM-LCSC-1M

Reviews:

Related manuals for CAB-SM-LCSC-1M

Brands by name

Popular brands

Cisco CAB-SM-LCSC-1M, Installation Notes

Search results

Summary of Contents for CAB-SM-LCSC-1M

Reviews:

Related manuals for CAB-SM-LCSC-1M

Brands by name

Popular brands