Cisco C9124AXD Hardware Installation Manual Download Page 9

Page: 9 / 118

C H A P T E R

About the Cisco Catalyst 9124AX Series Outdoor
Access Point

•

Introduction to Cisco Catalyst 9124AX Series Outdoor Access Point, on page 1

•

Cisco Catalyst 9124AX Series Outdoor Access Point Features, on page 1

•

AP Model Numbers and Regulatory Domains, on page 3

•

Antennas and Radios, on page 4

Introduction to Cisco Catalyst 9124AX Series Outdoor Access
Point

Cisco Catalyst 9124AX Series Outdoor Access Point is a Wi-Fi 6 technology based outdoor access point.
This access point (AP) series has three models:

• Cisco Catalyst 9124AXI AP with omni antennas

• Cisco Catalyst 9124AXD AP with directional antennas

• Cisco Catalyst 9124AXE AP with external antennas

This AP series support the following Wi-Fi 6 features:

• 4x4:4SS on the 2.4-GHz and 5-GHz bands

• Orthogonal Frequency Division Multiple Access (OFDMA) on downlink and uplink supported

• Multi-User, Multiple Input, Multiple Output (MU-MIMO)

Cisco Catalyst 9124AX Series Outdoor Access Point Features

Cisco Catalyst 9124AX Series Outdoor APs are supported on Cisco Catalyst 9800 wireless controller-based
products, and have the following features:

• Two radios—a dual-band 5-GHz (4x4) flexible radio with 2.4-GHz and 4x4 5-GHz radio, and an Internet

of Things (IoT) radio that works with Bluetooth Low Energy (BLE) and other multiprotocol 802.15.4
devices.

Cisco Catalyst 9124AX Series Outdoor Access Point Hardware Installation Guide

Summary of Contents for C9124AXD























































































































Search results

Summary of Contents for C9124AXD

Reviews:

Brands by name

Popular brands

Cisco C9124AXD, Hardware Installation Manual

Search results

Summary of Contents for C9124AXD

Reviews:

Brands by name

Popular brands