Cisco C9124AXD Hardware Installation Manual Download Page 37

Page: 37 / 118

C H A P T E R

Unpacking Your Access Point

•

Package Contents, on page 29

•

Unpacking the Access Point, on page 29

•

Optional Tools and Hardware from Cisco, on page 30

•

Cisco Orderable Accessories, on page 30

•

Preinstallation Checks and Installation Guidelines, on page 32

•

Typical Access Point Installation Components, on page 32

Package Contents

Each AP package contains the following items:

• One C9124AXI or C9124AXD or C9124AXE Outdoor AP

• Ground lug and screws with lock washers

• CAT 5e RJ45 Ethernet port termination plug

• Weatherization tape and anticorrosion sealant

• Cisco product documentation and pointer card

Unpacking the Access Point

To unpack the AP, follow these steps:

Procedure

Step 1

Unpack and remove the AP and the accessory kit from the shipping box.

Step 2

Return the packing material to the shipping container and save it for future use.

Step 3

Verify that you have received following items:

• The access point

• Accessory kit (Ethernet port termination plug, ground lug kit)

Cisco Catalyst 9124AX Series Outdoor Access Point Hardware Installation Guide

Summary of Contents for C9124AXD























































































































Search results

Summary of Contents for C9124AXD

Reviews:

Brands by name

Popular brands

Cisco C9124AXD, Hardware Installation Manual

Search results

Summary of Contents for C9124AXD

Reviews:

Brands by name

Popular brands