Cisco C9124AXD Hardware Installation Manual Download Page 15 | Manualshive

Page: 15 / 118

background image

C H A P T E R

2

Hardware Features

This section describes the following hardware features of the C9124AXI-x, C9124AXD-x, and C9124AXE-x
models:

•

Access Point Views, Ports, and Connectors, on page 7

•

C9124AXI (Internal Antenna) Model: Antenna Radiation Patterns, on page 11

•

C9124AXD (Directional Antenna) Model: Antenna Radiation Patterns, on page 14

•

C9124AXE (External Antenna) Model: Antenna Radiation Patterns, on page 17

•

Supported External Antennas, on page 23

•

Power Sources, on page 26

Access Point Views, Ports, and Connectors

Cisco Catalyst 9124AX Series Outdoor AP has multiple options that you can use to power the AP or join the
AP to the controller. For information about connectors and ports for the AP models, see

Connectors and Ports

on the AP, on page 7

The illustrations in this document show all the available connections for the AP. The connector plugs seal the
unused connection ports to ensure that the AP is watertight. Liquid-tight adapters are provided for connector
openings. You can install the adapters before or after deploying the AP.

Note

Connectors and Ports on the AP

The following illustrations show the different connector and port options available on the base and sides of
the AP.

Cisco Catalyst 9124AX Series Outdoor Access Point Hardware Installation Guide

7

«
...
13
14
15
16
17
...
»

Summary of Contents for C9124AXD























































































































Reviews:

No comments

Related manuals for C9124AXD

Brand: Navini Networks Pages: 8

Brand: Sagido Pages: 82

Brand: Ubiquiti Pages: 32

Brand: Hawking Pages: 2

Brand: Gemtek Pages: 35

Brand: Systimax Pages: 197

Brand: Anaren Pages: 27

Bridge/Router G-2000s

Brand: ZyXEL Communications Pages: 22

Brand: Modecom Pages: 48

Brand: Zonet Pages: 45

Brand: D-Link Pages: 40

Brand: D-Link Pages: 94

Brand: Samsung Pages: 4

Brand: Samsung Pages: 5

LTE Mobile HotSpot PRO

Brand: Samsung Pages: 2

Brand: Samsung Pages: 12

Brand: Samsung Pages: 8

Brand: Samsung Pages: 26

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands