manualshive.com logo in svg

Cisco C-series Nexus 5010, Hardware Installation Manual, Page: 50 / 52

Share
Download
Cisco C-series Nexus 5010 Hardware Installation Manual Download Page 50

 

1-50

Cisco Nexus 5000 Series Hardware Installation Guide

 

Chapter 1      Overview

    Cisco Nexus 5000 Platform Switches

Figure 1-57

Cisco Nexus 5010 Fan Module

The bicolor fan module LED indicates the fan tray health. Green indicates normal operation, while 
amber indicates a fan failure.

Transceivers

The Cisco Nexus 5010 switch supports both SFP+ Ethernet transceivers and SFP Fibre Channel 
transceivers. 

This section includes the following topics:

•

SFP+ Transceivers, page 1-50

•

SFP+ Copper Cables, page 1-51

•

SFP Fibre Channel Transceivers, page 1-51

SFP+ Transceivers

The enhanced SFP+ 10-Gigabit Ethernet transceiver module is a bidirectional device with a transmitter 
and receiver in the same physical package. It has a 20-pin connector on the electrical interface and 
duplex LC connector on the optical interface. The Cisco Nexus 5010 switch supports the following SFP+ 
optical transceivers: 

•

SR

•

LR (for uplink only)

239201

2

3

1

1

Handle

3

Captive screw

2

Fan module LED

Table 1-11

SFP+ Transceivers

Model

Description

SFP-10G-SR

10-Gigabit Ethernet—Short range SFP+ module

SFP-10G-LR

10-Gigabit Ethernet—Long range SFP+ module

Summary of Contents for C-series Nexus 5010





















































Reviews:

No comments