Cisco BTS 10200 Troubleshooting Manual Download Page 20

Page: 20 / 62

1-14

Cisco BTS 10200 Softswitch ISDN Provisioning and Troubleshooting

OL-12436-02

Chapter 1 ISDN Provisioning

Cisco BTS 10200 Provisioning

International PRI Setup

This section describes how to provision the Cisco BTS 10200 Softswitch for International PRI.
International PRI uses the International Telecommunications Union (ITU)/European
Telecommunication Standards Institute (ETSI) standard.

Note

ITU/ETSI uses a primary net-5 switch.

Step 1

Configure PRI FAS.

Figure 1-8

shows a sample configuration for Facility Associated Signaling (FAS).

Figure 1-8

Sample Configuration for FAS

Add ISDN D-channel profile with the nfas-supp token set to N.

add isdn-dchan-profile ID=NI2; description=dallas isdn dchan profile no.1;

type=SWV-ETSI-PRI; interface-type=network; isdn-restart-pri-supp=Y;

isdn-restart-interface-supp=y;isdn-service-supp=n; isdn-restart-chan-supp=y;

isdn-farend-init=n;isdn-query-supp=n;nfas-supp=n; bchan-neg-supp=y; t-301=300;

t-302=10; t-303=4; t-305=30;t-308=4; t-309=90;t-310=10; t-316=30; t-321=20;t-322=4;

t-323=30;

Note

See the

“ISDN Profiles” section on page 1-16

for more information.

Add the ISDN interfaces.

add isdn-intf isdn-dchan-id=100; INTF=0;

Add the ISDN D channels using the backhaul session set ID added in Step 2c in the

“Provisioning”

section on page 1-5

and the ISDN interfaces added in Step 1b.

add isdn-dchan id=100; backhaul-type=RUDP;set-id=backset1; DCHAN-SLOT=0;

DCHAN-PORT=1; DCHAN-TYPE=primary; DCHAN-INTF=0; isdn-dchan-profile-id=NI2;

Add an ISDN trunk group profile.

add isdn-tg-profile id=dallas1; chrg-num-supp=Y;

Add the ISDN trunk groups using the ISDN trunk group profile added in Step 1d.

add trunk-grp id=100; call-agent-id=CA146;tg-type=ISDN; tg-profile-id=ISDN1;

glare=all; mgcp-pkg-type=T; dial-plan-id=dp1; dial-plan-id=dp1; isdn-dchan-id=100;

Note

For ISDN trunk groups, the mgcp-pkg-type token must be set to T.

119619

Interface - 0

CIC start

D Channel

CIC end

Trunk group (100)

Summary of Contents for BTS 10200































































Search results

Summary of Contents for BTS 10200

Reviews:

Related manuals for BTS 10200

Brands by name

Popular brands

Cisco BTS 10200, Troubleshooting Manual

Search results

Summary of Contents for BTS 10200

Reviews:

Related manuals for BTS 10200

Brands by name

Popular brands