manualshive.com logo in svg

Cisco BTS 10200 Softswitch, Troubleshooting Manual

Share
Download
Cisco BTS 10200 Softswitch Troubleshooting Manual Download Page 855

 

C-11

Cisco BTS 10200 Softswitch Troubleshooting Guide, Release 5.0.x

OL-8723-19

Appendix C      Overload Control

Operating

Service Interaction Manager Measurements 

Table C-5

 lists the new Service Interaction Manager measurements provided to support this feature.

Traffic Measurements Monitor Counters

Table C-6

 lists the new Traffic Measurements Monitor (TMM) measurements provided to support this 

feature.

Table C-5

Service Interaction Manager Measurements used by Overload Control

Measurement

Description

SIM_OC_TRIG_FILTERED 

The number of triggers dropped when the FS is overloaded (a single counter is 
used by SIM, which tracks the trigger filtering for all the FS). SIM will update 
this counter every time it filters a trigger due to congestion on a FS.

SIM_OC_EMG_TRIG_FORCED

The number of emergency triggers (i.e. TRIGGER_911) forced when the FS is 
overloaded (a single counter is used by SIM which tracks number of emergency 
triggers forced for all the FS). SIM will update this counter every time when it 
forces an emergency trigger (TRIGGER_911) to FS. 

SIM_OC_TRIG_FORCED

The number of triggers forced when the FS is overloaded (a single counter is 
used by SIM which tracks the number of forced triggers for all the FSs). SIM 
will update this counter every time when it forces a trigger.

Table C-6

TMM Timers used by Overload Control

Measurement

Description

SIA_OC_RX_INVITE_REJECT

The total number of incoming INVITE messages rejected by 
SIA due to overload.

SIA_OC_RX_REGISTER_REJECT

The total number of incoming REGISTER messages rejected 
by SIA due to overload

SIA_OC_RX_REFER_REJECT

The total number incoming REFER messages rejected by SIP 
due to overload.

SIA_OC_RX_SUBSCRIBE_REJECT

The total number of incoming SUBSCRIBE messages 
rejected.

SIA_OC_RX_UNSOL_NOTIFY_SUPP

The total number of unsolicited notification requests 
suppressed without sending to endpoints.

SIA_OC_RX_OPTIONS_REJECT

The total number of  incoming OPTIONS messages rejected 
by SIA due to overload.

Summary of Contents for BTS 10200 Softswitch











































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands