manualshive.com logo in svg

Cisco BTS 10200 Softswitch, Troubleshooting Manual

Share
Download
Cisco BTS 10200 Softswitch Troubleshooting Manual Download Page 560

 

12-14

Cisco BTS 10200 Softswitch Troubleshooting Guide, Release 5.0.x

OL-8723-19

Chapter 12      System Troubleshooting

Troubleshooting System Alarms

Troubleshooting System Alarms

This section provides the information needed to monitor and correct system alarms. 

Table 12-3

 lists all 

of the system alarms in numerical order and provides cross reference to each subsection in this section.

Inter-Process Communication Queue Read Failure—System (2)

The Inter-Process Communication Queue Read Failure alarm (minor) indicates that the IPC queue read 
has failed. The primary cause of the alarm is that there is a problem with IPC communication. To correct 
the primary cause of the alarm, contact Cisco TAC.

Note

Refer to the 

“Obtaining Documentation and Submitting a Service Request” section on page lvi

 for 

detailed instructions on contacting Cisco TAC and opening a service request.

Table 12-3

BTS 10200 System Alarms 

Alarm Type

Alarm Name

Alarm Severity

SYSTEM(2)

Inter-Process Communication Queue Read Failure—System (2)

MINOR

SYSTEM(3)

Inter-Process Communication Message Allocate Failure—System (3)

MINOR

SYSTEM(4)

Inter-Process Communication Message Send Failure—System (4)

MINOR

SYSTEM(6)

Index List Insert Error—System (6)

MINOR

SYSTEM(7)

Index List Remove Error—System (7)

MINOR

SYSTEM(8)

Thread Creation Failure—System (8)

MAJOR

SYSTEM(10)

Index Update Registration Error—System (10)

MINOR

SYSTEM(11)

Index Table Add Entry Error—System (11)

MINOR

SYSTEM(12)

Software Error—System (12)

MAJOR

SYSTEM(13)

Multiple Readers and Multiple Writers Maximum Q Depth Reached—System (13)

CRITICAL

SYSTEM(14)

Multiple Readers and Multiple Writers Queue Reached Low Queue Depth—System 
(14)

MINOR

SYSTEM(15)

Multiple Readers and Multiple Writers Throttle Queue Depth Reached—System (15)

MAJOR

Summary of Contents for BTS 10200 Softswitch











































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands