Cisco BTS 10200 Softswitch Troubleshooting Manual Download Page 215

Page: 215 / 874

6-21

Cisco BTS 10200 Softswitch Troubleshooting Guide, Release 5.0.x

OL-8723-19

Chapter 6 Database Troubleshooting

Monitoring Database Events

This section provides the information needed to monitor and correct database events.

Table 6-2

lists all

of the database events in numerical order and provides cross reference to each subsection in this section.

Table 6-2

BTS 10200 Database Events

Event Type

Event Name

Event Severity

DATABASE(1)

Test Report—Database (1)

INFO

DATABASE(2)

Database Management Update Failure: Master/Slave Database Out of
Sync—Database (2)

WARNING

DATABASE(3)

There are Errors in Element Management System Database DefError Queue; Contact
Database Administrator—Database (3)

CRITICAL

DATABASE(4)

Element Management System Database HeartBeat: Replication PUSH Job
Broken—Database (4)

CRITICAL

DATABASE(5)

Element Management System Database HeartBeat Process Died—Database (5)

CRITICAL

DATABASE(6)

Element Management System Database Replication DefTranDest Queue
Overloaded—Database (6)

MAJOR

DATABASE(7)

Element Management System Database DefTran Queue is Overloaded—Database (7)

MINOR

DATABASE(8)

Element Management System Database Tablespace is Out of Free Space—Database
(8)

MAJOR

DATABASE(9)

Urgent: Element Management System Database Archive Log Directory is Getting
Full—Database (9)

CRITICAL

DATABASE(10)

Element Management System Database: Backup Fails—Database (10)

MAJOR

DATABASE(11)

Element Management System Database Alert.log Alerts—Database (11)

MAJOR

DATABASE(12)

Element Management System Database Process Died—Database (12)

CRITICAL

DATABASE(13)

Element Management System Database Performance Alert—Database (13)

MAJOR

DATABASE(14)

Table Size Exceeds Minor Threshold Limit—Database (14)

MINOR

DATABASE(15)

Table Size Exceeds Major Threshold Limit—Database (15)

MAJOR

DATABASE(16)

Table Size Exceeds Critical Threshold Limit—Database (16)

CRITICAL

DATABASE(17)

Data Replication Failed—Database (17)

MAJOR

DATABASE(18)

Unexpected Runtime Data Interaction—Database (18)

WARNING

DATABASE(19)

Daily Database Backup Completed Successfully—Database (19)

INFO

DATABASE(20)

Replication Data Flush Timeout During Switchover—Database (20)

MAJOR

DATABASE(21)

Database Statistics Collection Exception—Database (21)

MINOR

DATABASE(22)

Unprovisioned Language—Database (22)

MAJOR

DATABASE(23)

Element Management System Oracle Database–Minor Error—Database (23)

MINOR

DATABASE(24)

Element Management System Oracle Database–Major Error—Database (24)

MAJOR

DATABASE(25)

Secure File Transfer Protocol Transfer Failed—Database (25)

MAJOR

DATABASE(26)

File Write Error—Database (26)

MAJOR

DATABASE(27)

Failure Setting the Index Table Soft Limit—Database (27)

MAJOR

Summary of Contents for BTS 10200 Softswitch











































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for BTS 10200 Softswitch

Reviews:

Brands by name

Popular brands

Cisco BTS 10200 Softswitch, Troubleshooting Manual

Search results

Summary of Contents for BTS 10200 Softswitch

Reviews:

Brands by name

Popular brands